EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

The comparison of the accuracy of temporary crowns fabricated with several 3D printers and a milling machine

Junsik Lee iD, Sungwon Ju iD, Jihyung Kim iD, Sion Hwang iD, Jinsoo Ahn iD

The Journal of Advanced Prosthodontics · 2023 · 15 (2) · 72

DOI: 10.4047/jap.2023.15.2.72 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Advanced Prosthodontics, 2023. Verfasst von Junsik Lee und 4 weiteren Autor:innen. Beteiligte Einrichtung: Dental Research Institute and Department of Dental Biomaterials Science, School of Dentistry, Seoul National University, Seoul, Republic of Korea. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: National Research Foundation of Korea.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: The purpose of this in vitro study was to compare the accuracy of various 3D printers and a milling machine. MATERIALS AND METHODS: The die model was designed using CAD (Autodesk Inventor 2018 sp3). The 30 µm cement space was given to the die and the ideal crown of the mandibular left first molar was designed using CAD (ExoCAD). The crowns were produced using the milling machine (Imes-icore 250i) and the 3D printers (Zenith U, Zenith D, W11) and they were divided into four groups. In all groups, the interior of each crown was scanned (Identica blue) and superimposed (Geomagic Control X) with the previously designed die. The difference between the die and the actual crown was measured at specific points. The Kruskal-Wallis test, the Mann-Whitney test, and Bonferroni's method were performed with a statistical analysis software (P < .008 in inter-group comparison P < .001 in intra-group comparison). RESULTS: In all groups, the center of the occlusal area and the anti-rotational dimple area showed significantly greater difference and the marginal area showed the smallest difference comparatively. The mean value of the difference in each area and the sum of the differences were higher in order of W11, Imes-icore 250i, Zenith D, and Zenith U. CONCLUSION: The digital light processing (DLP) method shows higher accuracy compared to the sereolithography (SLA) method using the same resin material.

Schlagwörter

Stichwörter der Autor:innen

3D printerAdditive manufacturingCAD-CAMDigital light processingTemporary crown

Autor:innen und Institutionen

  • Dental Research Institute and Department of Dental Biomaterials Science, School of Dentistry, Seoul National University, Seoul, Republic of Korea.
  • L Dental Hospital, Seoul, Republic of Korea.

ORCID-Profile: Junsik Lee, Sungwon Ju, Jihyung Kim, Sion Hwang, Jinsoo Ahn

Förderung

  • National Research Foundation of Korea

Zitieren

APA

Lee, J., Ju, S., Kim, J., Hwang, S., & Ahn, J. (2023). The comparison of the accuracy of temporary crowns fabricated with several 3D printers and a milling machine. The Journal of Advanced Prosthodontics, 15(2), 72. https://doi.org/10.4047/jap.2023.15.2.72

Vancouver

Lee J, Ju S, Kim J, Hwang S, Ahn J. The comparison of the accuracy of temporary crowns fabricated with several 3D printers and a milling machine. The Journal of Advanced Prosthodontics. 2023;15(2):72. doi:10.4047/jap.2023.15.2.72

BibTeX
@article{Lee2023,
  author = {Lee, Junsik and Ju, Sungwon and Kim, Jihyung and Hwang, Sion and Ahn, Jinsoo},
  title = {The comparison of the accuracy of temporary crowns fabricated with several 3D printers and a milling machine},
  journal = {The Journal of Advanced Prosthodontics},
  year = {2023},
  volume = {15},
  number = {2},
  pages = {72},
  doi = {10.4047/jap.2023.15.2.72}
}
Kostenlos starten →