EUVIMEDEUVIMED entdecken
Crossref

Evaluation of the influence of gingival retraction width on the optical impression of the subgingival region using a 3D printed abutment tooth model

Takahiro Nishiyama, Kazumichi Wakabayashi, Miyu Tanaka, Shingo Tamiya, Takashi Nakamura, Shoichi Ishigaki

Dental Materials Journal · 2025

DOI: 10.4012/dmj.2024-269 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dental Materials Journal, 2025. Verfasst von Takahiro Nishiyama und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Fixed Prosthodontics, Osaka University Graduate School of Dentistry. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Dental Impression Technique, Models, Dental, Dental Abutments. Die Arbeit nennt 10 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study aimed to evaluate the conditions for the finish line position and gingival retraction width that allow for taking optical impressions using three-dimensional (3D) printed models. Taking an impression using an intraoral scanner (IOS) is widely performed in fabricating crown prostheses. Measuring the subgingival finish line using an IOS is difficult; to obtain optical impressions of the subgingival finish line, the gingival retraction has been recommended. However, no study has evaluated the amount of gingival retraction width and the depth of the finish line. In this study, the measurement limits of the subgingival finish line using an IOS and models fabricated by a 3D printer were investigated. The results of this study revealed that TRIOS3 could not measure the finish line when the gingival retraction width was 0.50 mm below the gingival margin.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDental Impression TechniqueModels, DentalDental AbutmentsGingivaGingival Retraction TechniquesHumansDental Prosthesis DesignCrowns

Stichwörter der Autor:innen

Finish lineGingival retractionIntraoral scannerOptical impressionSubgingival region

Autor:innen und Institutionen

  • Department of Fixed Prosthodontics, Osaka University Graduate School of Dentistry.
  • Department of Oral Health Sciences, Otemae College.

Zitieren

APA

Nishiyama, T., Wakabayashi, K., Tanaka, M., Tamiya, S., Nakamura, T., & Ishigaki, S. (2025). Evaluation of the influence of gingival retraction width on the optical impression of the subgingival region using a 3D printed abutment tooth model. Dental Materials Journal. https://doi.org/10.4012/dmj.2024-269

Vancouver

Nishiyama T, Wakabayashi K, Tanaka M, Tamiya S, Nakamura T, Ishigaki S. Evaluation of the influence of gingival retraction width on the optical impression of the subgingival region using a 3D printed abutment tooth model. Dental Materials Journal. 2025. doi:10.4012/dmj.2024-269

BibTeX
@article{Nishiyama2025,
  author = {Nishiyama, Takahiro and Wakabayashi, Kazumichi and Tanaka, Miyu and Tamiya, Shingo and Nakamura, Takashi and Ishigaki, Shoichi},
  title = {Evaluation of the influence of gingival retraction width on the optical impression of the subgingival region using a 3D printed abutment tooth model},
  journal = {Dental Materials Journal},
  year = {2025},
  doi = {10.4012/dmj.2024-269}
}
Kostenlos starten →