EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Surface Roughness on Aerodynamic Performance of the Wing with NACA 2412 Airfoil

Yagya Dutta Dwivedi, Samreen Tabassum, Sonnakula Madhumitha, Banoth Karthik

WSEAS Transactions on Applied and Theoretical Mechanics · 20.11.2026 · 22 · 80

DOI: 10.37394/232011.2027.22.7 ↗

Kurz gefasst

Fachartikel in der Zeitschrift WSEAS Transactions on Applied and Theoretical Mechanics, online erschienen am 20.11.2026. Verfasst von Yagya Dutta Dwivedi und 3 weiteren Autor:innen. Die Arbeit nennt 10 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The surface roughness over the wing is one of the primary factors affecting the aerodynamic performance of the airplane. The surface roughness is likely to alter the boundary layer thickness over the wing. This alteration of the boundary layer thickness will alter the lift and drag forces and also the ratio of the lift to drag, which is called aerodynamic performance. In this research paper, the effects of two different roughness values, i.e., 12-grit (0.0015 m), which is coarse, and 320-grit (5 × 10⁻⁷ m), which is very smooth and normally used for polishing surfaces, on aerodynamic performance are evaluated and compared with a smooth conventional NACA 2412 airfoil. The surface roughness is applied at 40- 50% of the chord length from the leading edge of the airfoil. The CAD models were prepared as per the roughness, and computational fluid dynamics (CFD) analysis was carried out using Ansys Fluent. The simulations are performed at the chord Reynolds number of 5×10⁵ and angles of attack (AOA) of 00, 50, 100, and 150. The results showed that the lift coefficient (CL) increases up to 100 AOA for all three types of roughness, and at 150 AOA the CL falls sharply for both rough surfaces, but the smooth surface provides a better CL. The coefficient of drag (CD) for the 320-grit roughness airfoil was found to be much better than the other two conditions, i.e., the smooth and 12-grit roughness conditions. The fine roughness configuration (320-grit) and conventional smooth surface wing exhibited better aerodynamic performance comparable to the 12-grit roughness (most rough surface) conditions. These surfaces showed improved flow attachment at moderate AOA. On the other hand, the 12-grit coarse roughness configuration resulted in high CD and low CL and hence low aerodynamic performance (CL/CD ratio). The final finding is that the aerodynamic performance for the 320-grit rough surface is best up to 100 AOA, but at higher AOA the smooth conventional surface wing is only suitable.

Zitieren

APA

Dwivedi, Y. D., Tabassum, S., Madhumitha, S., & Karthik, B. (2026). Effect of Surface Roughness on Aerodynamic Performance of the Wing with NACA 2412 Airfoil. WSEAS Transactions on Applied and Theoretical Mechanics, 22, 80. https://doi.org/10.37394/232011.2027.22.7

Vancouver

Dwivedi YD, Tabassum S, Madhumitha S, Karthik B. Effect of Surface Roughness on Aerodynamic Performance of the Wing with NACA 2412 Airfoil. WSEAS Transactions on Applied and Theoretical Mechanics. 2026;22:80. doi:10.37394/232011.2027.22.7

BibTeX
@article{Dwivedi2026,
  author = {Dwivedi, Yagya Dutta and Tabassum, Samreen and Madhumitha, Sonnakula and Karthik, Banoth},
  title = {Effect of Surface Roughness on Aerodynamic Performance of the Wing with NACA 2412 Airfoil},
  journal = {WSEAS Transactions on Applied and Theoretical Mechanics},
  year = {2026},
  volume = {22},
  pages = {80},
  doi = {10.37394/232011.2027.22.7}
}
Kostenlos starten →