EUVIMEDEUVIMED entdecken
Crossref

Mechanical Evaluation of Additively Manufactured Polymer Rings for Circular External Fixators

Bartosz Martyniuk, Dominika Rejniak, Piotr Morasiewicz, Jarosław Filipiak

Acta of Bioengineering and Biomechanics · 12.02.2026 · 27 (**4) · 149-159

DOI: 10.37190/abb/217504 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Acta of Bioengineering and Biomechanics, online erschienen am 09.02.2026. Verfasst von Bartosz Martyniuk und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanics, Materials and Biomedical Engineering, Wrocław University of Science and Technology, Wrocław, Poland. Hauptthemen laut MEDLINE: Polymers, External Fixators, Materials Testing.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The aim of this study was to assess the feasibility of using additively manufactured polymer rings as structural components of circular external fixators for limb lengthening in pediatric patients. The analysis focused on whether such rings can provide sufficient mechanical performance while simultaneously reducing device mass and improving radiographic transparency compared with conventional metallic solutions.

Methods

Two design variants of circular rings with different cross sectional geometries were developed and manufactured using fused filament fabrication from a thermoplastic polymer. Their mechanical behavior was assessed through numerical finite element simulations and experimental testing. Radial and axial loading conditions corresponding to clinical use were analyzed at the ring level. Subsequently, complete external fixator assemblies incorporating the printed rings were constructed and subjected to quasi static axial compression tests. Comparative radiographic imaging was also conducted to evaluate the influence of polymer based rings on image quality relative to conventional aluminum rings.

Results

The polymer rings exhibited lower radial stiffness than aluminum reference rings; however, the resulting deformations were elastic, repeatable, and associated with stress levels below the material yield limit. External fixators equipped with printed rings demonstrated axial stiffness values within the range reported for conventional circular fixators used in clinical practice. In addition, the polymer based configurations showed a notable reduction in mass and significantly improved radiographic transparency compared with metallic systems.

Conclusions

Additively manufactured polymer rings with appropriately optimized geometry can provide mechanically acceptable performance for use in circular external fixators, while offering advantages in weight reduction and radiographic assessment.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolymersExternal FixatorsMaterials TestingFinite Element AnalysisStress, MechanicalHumansBiomechanical Phenomena

Stichwörter der Autor:innen

additive manufacturingbiomechanical analysiscircular external fixatorfinite element methodmechanical stiffnesspolymer rings

Substanzen

Polymers

Autor:innen und Institutionen

  • Department of Mechanics, Materials and Biomedical Engineering, Wrocław University of Science and Technology, Wrocław, Poland.
  • Wrocław University of Science and Technology, Wrocław, Poland.
  • Department of Orthopaedic and Trauma Surgery, Institute of Medical Sciences, University of Opole, Opole, Poland.

Zitieren

APA

Martyniuk, B., Rejniak, D., Morasiewicz, P., & Filipiak, J. (2026). Mechanical Evaluation of Additively Manufactured Polymer Rings for Circular External Fixators. Acta of Bioengineering and Biomechanics, 27(**4), 149-159. https://doi.org/10.37190/abb/217504

Vancouver

Martyniuk B, Rejniak D, Morasiewicz P, Filipiak J. Mechanical Evaluation of Additively Manufactured Polymer Rings for Circular External Fixators. Acta of Bioengineering and Biomechanics. 2026;27(**4):149-159. doi:10.37190/abb/217504

BibTeX
@article{Martyniuk2026,
  author = {Martyniuk, Bartosz and Rejniak, Dominika and Morasiewicz, Piotr and Filipiak, Jarosław},
  title = {Mechanical Evaluation of Additively Manufactured Polymer Rings for Circular External Fixators},
  journal = {Acta of Bioengineering and Biomechanics},
  year = {2026},
  volume = {27},
  number = {**4},
  pages = {149--159},
  doi = {10.37190/abb/217504}
}
Kostenlos starten →