EUVIMEDEUVIMED entdecken
Crossref

Influence of laser power and hatch spacing on the mechanical properties of AlSi10Mg processed by selective laser melting

Xabier Sandua, Eneko Arbizu, Álvaro Rodríguez, Fernando Veiga, Miguel Ángel Martín, Pedro J. Rivero

Materials Science in Additive Manufacturing · 18.05.2026 · 5 (2) · 026040008

DOI: 10.36922/msam026040008 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials Science in Additive Manufacturing, online erschienen am 18.05.2026. Verfasst von Xabier Sandua und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Selective laser melting (SLM) of AlSi10Mg is widely used for lightweight engineering applications, but the combined effects of key process parameters on densification, microstructure, and mechanical performance remain incompletely understood. This study systematically investigated the combined effects of laser power (200–230 W) and hatch spacing (0.11–0.15 mm) on the densification, mechanical behavior, and microstructural characteristics of AlSi10Mg components fabricated by SLM. A statistically rigorous approach based on two-way ANOVA and ordinary least squares regression was employed to quantify the individual and interactive influence of process parameters on relative density, surface porosity, hardness, Charpy impact energy, and tensile properties. The results show that laser power is the dominant parameter affecting densification and impact energy, whereas hatch spacing exhibits no statistically significant influence within the investigated range. Maximum relative densities above 99.7% were achieved at low laser powers (200–210 W), while hardness increased with increasing power, reaching approximately 140 HV at 230 W. The highest impact energy was obtained at an intermediate laser power of 210 W, indicating a favorable intermediate energy input under the tested conditions. Tensile testing revealed that the highest ultimate tensile strength was achieved at 220 W with a hatch spacing of 0.15 mm, despite slightly lower density and hardness values compared to other samples. Microstructural and fractographic analyses demonstrate that tensile performance is strongly governed by solidification morphology and defect distribution rather than density alone. This systematic, statistically supported evaluation advances the understanding of process–property relationships in SLM AlSi10Mg and provides practical guidance for parameter optimization in engineering applications.

Zitieren

APA

Sandua, X., Arbizu, E., Rodríguez, Á., Veiga, F., Martín, M. Á., & Rivero, P. J. (2026). Influence of laser power and hatch spacing on the mechanical properties of AlSi10Mg processed by selective laser melting. Materials Science in Additive Manufacturing, 5(2), 026040008. https://doi.org/10.36922/msam026040008

Vancouver

Sandua X, Arbizu E, Rodríguez Á, Veiga F, Martín MÁ, Rivero PJ. Influence of laser power and hatch spacing on the mechanical properties of AlSi10Mg processed by selective laser melting. Materials Science in Additive Manufacturing. 2026;5(2):026040008. doi:10.36922/msam026040008

BibTeX
@article{Sandua2026,
  author = {Sandua, Xabier and Arbizu, Eneko and Rodríguez, Álvaro and Veiga, Fernando and Martín, Miguel Ángel and Rivero, Pedro J.},
  title = {Influence of laser power and hatch spacing on the mechanical properties of AlSi10Mg processed by selective laser melting},
  journal = {Materials Science in Additive Manufacturing},
  year = {2026},
  volume = {5},
  number = {2},
  pages = {026040008},
  doi = {10.36922/msam026040008}
}
Kostenlos starten →