EUVIMEDEUVIMED entdecken
Crossref

Microstructure evolution and ductility improvement of additively manufactured biodegradable zinc–magnesium alloys via annealing

Changjun Han, Jinmiao Huang, Xiangling Ye, Boxun Liu, Zhi Dong, Yongqiang Yang, Junqing Gao, Kuangyang Yang, Guocai Chen

International Journal of Bioprinting · 08.05.2024 · 10 (4) · 3034

DOI: 10.36922/ijb.3034 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Bioprinting, online erschienen am 08.05.2024. Verfasst von Changjun Han und 8 weiteren Autor:innen. Die Arbeit wurde bisher 22-mal zitiert (Crossref).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Zinc–magnesium (Zn–Mg) alloys, fabricated by laser powder bed fusion (LPBF) additive manufacturing techniques, have emerged as promising candidates for biomedical implants due to their biodegradation capability, superior mechanical strength, and excellent biocompatibility. However, LPBF-fabricated Zn–Mg alloys still face challenges related to extremely low ductility and limited exploration of degradation characteristics. In this study, the impact of Mg incorporation on the printability, degradation properties, microstructure, and mechanical properties of LPBF-fabricated Zn–Mg alloys was primarily investigated. Furthermore, we proposed a viable annealing post-processing route for the first time to tailor the microstructural characteristics of the fabricated Zn–Mg alloy and enhanced its limited ductility. The results demonstrated that by applying a laser power of 80 W and a scanning speed of 600 mm/s, the relative density of LPBF-fabricated Zn–Mg alloy reached 98.62%. Increasing the Mg amount from 1 to 5 wt% refined the grain size while promoting an increase in Mg2Zn11 and MgZn2 phases. Among these compositions, the Zn–1Mg alloy exhibited the greatest degradation rate at 0.126 mm/year. The annealing treatment facilitated the microstructure evolution of the Zn–1Mg alloy, resulting in equiaxed grains, increased average grain size, high-angle grain boundaries, and enrichment of Mg at grain boundaries. After annealing at 300°C for 0.5 h, the tensile strength of Zn– 1Mg alloy decreased from 254.92 to 170.93 MPa, while the elongation significantly increased by a factor of 14.3 from 0.55% to 8.43%. These findings provide valuable insights into an effective post-processing approach for tailoring the microstructure and resultant mechanical properties of LPBF-fabricated Zn and its alloys.

Zitieren

APA

Han, C., Huang, J., Ye, X., Liu, B., Dong, Z., Yang, Y., Gao, J., Yang, K., & Chen, G. (2024). Microstructure evolution and ductility improvement of additively manufactured biodegradable zinc–magnesium alloys via annealing. International Journal of Bioprinting, 10(4), 3034. https://doi.org/10.36922/ijb.3034

Vancouver

Han C, Huang J, Ye X, Liu B, Dong Z, Yang Y, et al. Microstructure evolution and ductility improvement of additively manufactured biodegradable zinc–magnesium alloys via annealing. International Journal of Bioprinting. 2024;10(4):3034. doi:10.36922/ijb.3034

BibTeX
@article{Han2024,
  author = {Han, Changjun and Huang, Jinmiao and Ye, Xiangling and Liu, Boxun and Dong, Zhi and Yang, Yongqiang and Gao, Junqing and Yang, Kuangyang and Chen, Guocai},
  title = {Microstructure evolution and ductility improvement of additively manufactured biodegradable zinc–magnesium alloys via annealing},
  journal = {International Journal of Bioprinting},
  year = {2024},
  volume = {10},
  number = {4},
  pages = {3034},
  doi = {10.36922/ijb.3034}
}
Kostenlos starten →