EUVIMEDEUVIMED entdecken
Crossref

DIRECTIONAL EFFECTS IN ROBOTIC MILLING OF UHMWPE: AN EMPIRICAL STUDY ON SURFACE ROUGHNESS

Wan Nor Shela Ezwane Wan Jusoh, Mohamad Irwan Yahaya, Shukri Zakaria, Mahamad Hisyam Mahamad Basri, Md Razak Daud

International Journal of Innovation and Industrial Revolution · 18.03.2026 · 8 (24) · 357

DOI: 10.35631/ijirev.824022 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Innovation and Industrial Revolution, online erschienen am 18.03.2026. Verfasst von Wan Nor Shela Ezwane Wan Jusoh und 4 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 23 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Industrial robots offer large workspaces and flexibility for machining, but their compliance-dominated dynamics can compromise surface quality. While vibration control in robotic machining is well studied for metals and fibre-reinforced composites, empirical guidance for soft-polymer finishing remains limited. As one of the first empirical studies on robotic finishing of UHMWPE, this work investigates the direction–compliance–roughness interaction by framing feed direction as a controllable parameter. This study explicitly demonstrates how feed direction interacts with pose-dependent compliance to systematically influence surface roughness in robotic milling of UHMWPE. This feasibility study investigates how feed direction affects surface roughness (Ra, Rq, Rz) in robotic milling of UHMWPE. Experiments were performed using a KUKA KR120 R2700 six-axis robot with fixed parameters: 9500 rpm spindle speed, 1080 mm/min feed rate, and dry finishing cuts at depths of 0.1, 0.2, and 0.3mm. Surface roughness metrics were measured via contact profilometry using a standardized evaluation length. Due to kinematic constraints, X–Y toolpaths require different joint configurations; therefore, observed differences reflect the combination of feed-direction and pose-dependent stiffness anisotropy. Y-direction feeding produced lower Ra (1.64–1.87 µm) than X-direction feeding (1.66–1.94 µm). In contrast, X-direction feeding yielded lower Rq (2.0–2.5 µm) with strong linear predictability (R² > 0.99), compared with Y-direction Rq (2.35–2.40 µm). Rz exhibited depth-dependent behavior, with X performing better at shallow depth (0.2 mm) and Y at 0.3 mm, while tool adhesion showed little directional dependence. Overall, the findings provide evidence of direction-dependent roughness trade-offs: Y-direction may be preferred for average smoothness (Ra), whereas X-direction may be preferred when peak-sensitive control (Rq/Rz) is critical.

Zitieren

APA

Jusoh, W. N. S. E. W., Yahaya, M. I., Zakaria, S., Basri, M. H. M., & Daud, M. R. (2026). DIRECTIONAL EFFECTS IN ROBOTIC MILLING OF UHMWPE: AN EMPIRICAL STUDY ON SURFACE ROUGHNESS. International Journal of Innovation and Industrial Revolution, 8(24), 357. https://doi.org/10.35631/ijirev.824022

Vancouver

Jusoh WNSEW, Yahaya MI, Zakaria S, Basri MHM, Daud MR. DIRECTIONAL EFFECTS IN ROBOTIC MILLING OF UHMWPE: AN EMPIRICAL STUDY ON SURFACE ROUGHNESS. International Journal of Innovation and Industrial Revolution. 2026;8(24):357. doi:10.35631/ijirev.824022

BibTeX
@article{Jusoh2026,
  author = {Jusoh, Wan Nor Shela Ezwane Wan and Yahaya, Mohamad Irwan and Zakaria, Shukri and Basri, Mahamad Hisyam Mahamad and Daud, Md Razak},
  title = {DIRECTIONAL EFFECTS IN ROBOTIC MILLING OF UHMWPE: AN EMPIRICAL STUDY ON SURFACE ROUGHNESS},
  journal = {International Journal of Innovation and Industrial Revolution},
  year = {2026},
  volume = {8},
  number = {24},
  pages = {357},
  doi = {10.35631/ijirev.824022}
}
Kostenlos starten →