EUVIMEDEUVIMED entdecken
Open Access

Ablation Depth and Surface Morphology of Dentin After Irradiation with a Tunable TEA-CO 2 Laser in the Wavelength Range of 9.3 – 10.6 µm

Hadiseh Ghalkhanbaz iD, Maryam Ilchi Ghazaani iD, Batool Sajad iD

Journal of Lasers in Medical Sciences · 03.05.2026 · 17 · e9

DOI: 10.34172/jlms.2026.09 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Lasers in Medical Sciences, online erschienen am 03.05.2026. Verfasst von Hadiseh Ghalkhanbaz und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Atomic and Molecular Physics, Faculty of Physics, Alzahra University, Tehran, Iran. Die Arbeit nennt 56 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

This study evaluated morphological and structural changes in extracted human dentin following irradiation with a pulsed tunable TEA-CO2 laser (9–11 μm) using scanning electron microscopy (SEM). The ablation rate was quantitatively determined at different wavelengths and pulse numbers while assessing preservation of dentinal tubules.

Methods

Nearly flat dentin specimens were irradiated at four wavelengths (9.3, 9.6, 10.3, and 10.6 μm) with a constant energy density of 7.36 J/cm², pulse width of 200 ns, and repetition rate of 1 Hz. Samples were grouped by cooling method (air or water) and exposed to 1, 5, 10, 20, or 30 pulses. Surface morphology was examined by optical microscopy and SEM. Single-pulse ablation depth and ablation rate (μm/pulse) were measured using a profilometer under sub-threshold thermal damage conditions. Dentinal tubule occlusion after single-shot irradiation was compared with untreated dentin controls.

Results

Air-cooled samples exhibited thermal damage, including carbonization and cracking. SEM analysis showed that water cooling led to greater thermal damage at high pulse numbers, particularly at wavelengths near 9 μm, corresponding to strong hydroxyapatite absorption and a lower ablation threshold. Up to 10 pulses, no cracks or peripheral thermal damage were observed at any wavelength. For single-pulse irradiation, the greatest ablation depth occurred at 10.3 μm with complete tubule occlusion, followed by 9.6 μm. At five pulses, maximum ablation depth was again observed at 10.3 μm (complete occlusion) and 9.3 μm (partial occlusion).

Conclusion

These findings indicate that appropriate selection of wavelength, pulse number, and cooling method enables controlled dentin removal using a pulsed TEA-CO2 laser without peripheral tissue damage. Wavelength-dependent absorption and cooling conditions are critical for optimizing ablation efficiency while preserving dentinal tubule integrity.

Schlagwörter

Stichwörter der Autor:innen

Air-water-coolingHuman dentin ablationMorphological studyThermal damageTunable TEA-CO2 laser

Autor:innen und Institutionen

  • Department of Atomic and Molecular Physics, Faculty of Physics, Alzahra University, Tehran, Iran.
  • Photonics and Quantum Technologies Research Institute, Nuclear Sciences and Technologies Research Institute (NSTRI), Tehran, Iran.

ORCID-Profile: Hadiseh Ghalkhanbaz, Maryam Ilchi Ghazaani, Batool Sajad

Zitieren

APA

Ghalkhanbaz, H., Ilchi Ghazaani, M., & Sajad, B. (2026). Ablation Depth and Surface Morphology of Dentin After Irradiation with a Tunable TEA-CO 2 Laser in the Wavelength Range of 9.3 – 10.6 µm. Journal of Lasers in Medical Sciences, 17, e9. https://doi.org/10.34172/jlms.2026.09

Vancouver

Ghalkhanbaz H, Ilchi Ghazaani M, Sajad B. Ablation Depth and Surface Morphology of Dentin After Irradiation with a Tunable TEA-CO 2 Laser in the Wavelength Range of 9.3 – 10.6 µm. Journal of Lasers in Medical Sciences. 2026;17:e9. doi:10.34172/jlms.2026.09

BibTeX
@article{Ghalkhanbaz2026,
  author = {Ghalkhanbaz, Hadiseh and Ilchi Ghazaani, Maryam and Sajad, Batool},
  title = {Ablation Depth and Surface Morphology of Dentin After Irradiation with a Tunable TEA-CO 2 Laser in the Wavelength Range of 9.3 – 10.6 µm},
  journal = {Journal of Lasers in Medical Sciences},
  year = {2026},
  volume = {17},
  pages = {e9},
  doi = {10.34172/jlms.2026.09}
}
Kostenlos starten →