EUVIMEDEUVIMED entdecken
Open Access

Immersion Phase Separation 3-Dimensional Printing for Strain-Stiffening Hydrogel Scaffolds

Muyuan Chai iD, Haolin Bu, Rui Zheng, Zhilu Yang, Xuetao Shi iD

Research · 2025-01 · 8

DOI: 10.34133/research.0742 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Research, online erschienen am 17.06.2025. Verfasst von Muyuan Chai und 4 weiteren Autor:innen. Beteiligte Einrichtung: Dongguan Key Laboratory of Smart Biomaterials and Regenerative Medicine, The Tenth Affiliated Hospital, Southern Medical University, Dongguan 523059,…. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: the National Key Research and Development Program of China, National Natural Science Foundation of China, Basic and Applied Basic Research Foundation of Guangdong Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Strain-stiffening hydrogels, which mimic the nonlinear mechanical behavior of biological tissues such as skin, arteries, and cartilage, hold transformative potential for biomedical applications. This study introduces immersion phase separation (IPS) 3-dimensional (3D) printing, an innovative technique that enables the one-step fabrication of strain-stiffening hydrogel scaffolds with intricate, hierarchical architectures. This technique addresses the long-standing challenge of balancing structural complexity and intrinsic mechanoresponsive behavior in traditional hydrogel fabrication methods. By leveraging dynamic hydrophobic interactions and solvent exchange kinetics, IPS 3D printing achieves multiscale control over pore architectures (5 to 200 μm) and anisotropic microchannels while preserving J-shaped stress–strain curves (fracture stress: ~0.7 MPa; elongation: >1,000%). The physically cross-linked network enables closed-loop recyclability (>95% material recovery) without performance degradation, while functional fillers (e.g., carbon nanotubes, copper, and hydroxyapatite) enhance properties such as electrical conductivity (2-orders-of-magnitude improvement) and real-time motion sensing capabilities. This platform facilitates the creation of patient-specific implants with tailored mechanical properties and paves the way for adaptive biohybrid devices that mimic the dynamic behavior of native tissues, holding promise for regenerative medicine, soft robotics, and advanced biomedical applications. IPS 3D printing uniquely resolves the trade-off between structural sophistication and functional biomimicry, establishing a paradigm for replicating dynamic biological tissues.

Autor:innen und Institutionen

  • Dongguan Key Laboratory of Smart Biomaterials and Regenerative Medicine, The Tenth Affiliated Hospital, Southern Medical University, Dongguan 523059, P. R. China.
  • National Engineering Research Centre for Tissue Restoration and Reconstruction, South China University of Technology, Guangzhou 510006, P. R. China.
  • School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640, P. R. China.
  • Key Laboratory of Biomedical Engineering of Guangdong Province, South China University of Technology, Guangzhou 510006, P. R. China.

ORCID-Profile: Muyuan Chai, Xuetao Shi

Förderung

  • the National Key Research and Development Program of China
  • National Natural Science Foundation of China
  • Basic and Applied Basic Research Foundation of Guangdong Province
  • Postdoctoral Fellowship Program of CPSF
  • China Postdoctoral Science Foundation

Zitieren

APA

Chai, M., Bu, H., Zheng, R., Yang, Z., & Shi, X. (2025). Immersion Phase Separation 3-Dimensional Printing for Strain-Stiffening Hydrogel Scaffolds. Research, 8. https://doi.org/10.34133/research.0742

Vancouver

Chai M, Bu H, Zheng R, Yang Z, Shi X. Immersion Phase Separation 3-Dimensional Printing for Strain-Stiffening Hydrogel Scaffolds. Research. 2025;8. doi:10.34133/research.0742

BibTeX
@article{Chai2025,
  author = {Chai, Muyuan and Bu, Haolin and Zheng, Rui and Yang, Zhilu and Shi, Xuetao},
  title = {Immersion Phase Separation 3-Dimensional Printing for Strain-Stiffening Hydrogel Scaffolds},
  journal = {Research},
  year = {2025},
  volume = {8},
  doi = {10.34133/research.0742}
}
Kostenlos starten →