EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical and Tribological Properties of FFF-Printed TPU 95A with Uniform and Step-Gradient Infill Architectures

Andrey P. Vasilev, Igor S. Makarov, Aitalina A. Okhlopkova

Technologies · 29.08.2026 · 14 (9) · 536

DOI: 10.3390/technologies14090536 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Technologies, online erschienen am 29.08.2026. Verfasst von Andrey P. Vasilev und 2 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the effects of uniform and symmetric step-gradient infill architectures on the density, mechanical properties, Shore D hardness, and dry-sliding coefficient of friction of FFF-printed thermoplastic polyurethane (TPU) 95A. Uniform triangular infills at 50%, 70%, and 90% were compared with a surface-dense architecture (GI-1: 90–70–50–70–90%) and a core-dense architecture (GI-2: 50–70–90–70–50%). The experimental density of GI-2 (0.988 g/cm3) did not differ significantly from that of the uniform 70% configuration (0.990 g/cm3). GI-2 nevertheless exhibited significantly higher tensile strength (20.3 vs. 18.4 MPa) and a higher work of deformation to failure (48.3 vs. 32.3 MJ/m3). GI-1 had a lower experimental density than the uniform 90% configuration yet higher tensile strength and work of deformation to failure; the two configurations were not density-matched. Both gradient architectures exhibited lower mean compressive stresses at 20% strain than the uniform 70% and 90% specimens. GI-1 displayed a Shore D hardness comparable to the uniform 90% configuration and the lowest mean coefficient of friction (0.50 ± 0.01). Overall, step-gradient infill can improve specific tensile properties while allowing compressive compliance and the contact response of the outer shell to be tailored separately. However, the effects of gradient order and material content could not be fully separated because GI-1 and GI-2 differed in nominal mean infill density.

Förderung

  • Russian Science Foundation

Zitieren

APA

Vasilev, A. P., Makarov, I. S., & Okhlopkova, A. A. (2026). Mechanical and Tribological Properties of FFF-Printed TPU 95A with Uniform and Step-Gradient Infill Architectures. Technologies, 14(9), 536. https://doi.org/10.3390/technologies14090536

Vancouver

Vasilev AP, Makarov IS, Okhlopkova AA. Mechanical and Tribological Properties of FFF-Printed TPU 95A with Uniform and Step-Gradient Infill Architectures. Technologies. 2026;14(9):536. doi:10.3390/technologies14090536

BibTeX
@article{Vasilev2026,
  author = {Vasilev, Andrey P. and Makarov, Igor S. and Okhlopkova, Aitalina A.},
  title = {Mechanical and Tribological Properties of FFF-Printed TPU 95A with Uniform and Step-Gradient Infill Architectures},
  journal = {Technologies},
  year = {2026},
  volume = {14},
  number = {9},
  pages = {536},
  doi = {10.3390/technologies14090536}
}
Kostenlos starten →