EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Increasing the Wear Resistance of Stamping Tools for Coordinate Punching of Sheet Steel Using CrAlSiN and DLC:Si Coatings

Sergey N. Grigoriev, Marina A. Volosova, Ilya A. Korotkov, Vladimir D. Gurin, Artem P. Mitrofanov, Sergey V. Fedorov, Anna A. Okunkova

Technologies · 12.01.2025 · 13 (1) · 30

DOI: 10.3390/technologies13010030 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Technologies, online erschienen am 12.01.2025. Verfasst von Sergey N. Grigoriev und 6 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education of the Russian Federation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The punching of holes or recesses on computer numerical control coordinate presses occurs in sheets at high speeds (up to 1200 strokes/min) with an accuracy of ~0.05 mm. One of the most effective approaches to the wear rate reduction of stamping tools is the use of solid lubricants, such as wear-resistant coatings, where the bulk properties of the tool are combined with high microhardness and lubricating ability to eliminate waste disposal and remove oil contaminants from liquid lubricants. This work describes the efficiency of complex CrAlSiN/DLC:Si coatings deposited using a hybrid unit combining physical vapor deposition and plasma-assisted chemical vapor deposition technologies to increase the wear resistance of a punch tool made of X165CrMoV12 die steel during coordinate punching of 4.0 mm thick 41Cr4 carbon structural steel sheets. The antifriction layer of DLC:Si allows for minimizing the wear under thermal exposure of 200 °C. The wear criterion of the lateral surface was 250 μm. The tribological tests allow us to consider the CrAlSiN/DLC:Si coatings as effective in increasing the wear resistance of stamping tools (21,000 strokes for the uncoated tool and 48,000 strokes for the coated one) when solving a wide range of technological problems in sheet stamping of structural steels.

Förderung

  • Ministry of Science and Higher Education of the Russian Federation

Zitieren

APA

Grigoriev, S. N., Volosova, M. A., Korotkov, I. A., Gurin, V. D., Mitrofanov, A. P., Fedorov, S. V., & Okunkova, A. A. (2025). Increasing the Wear Resistance of Stamping Tools for Coordinate Punching of Sheet Steel Using CrAlSiN and DLC:Si Coatings. Technologies, 13(1), 30. https://doi.org/10.3390/technologies13010030

Vancouver

Grigoriev SN, Volosova MA, Korotkov IA, Gurin VD, Mitrofanov AP, Fedorov SV, et al. Increasing the Wear Resistance of Stamping Tools for Coordinate Punching of Sheet Steel Using CrAlSiN and DLC:Si Coatings. Technologies. 2025;13(1):30. doi:10.3390/technologies13010030

BibTeX
@article{Grigoriev2025,
  author = {Grigoriev, Sergey N. and Volosova, Marina A. and Korotkov, Ilya A. and Gurin, Vladimir D. and Mitrofanov, Artem P. and Fedorov, Sergey V. and Okunkova, Anna A.},
  title = {Increasing the Wear Resistance of Stamping Tools for Coordinate Punching of Sheet Steel Using CrAlSiN and DLC:Si Coatings},
  journal = {Technologies},
  year = {2025},
  volume = {13},
  number = {1},
  pages = {30},
  doi = {10.3390/technologies13010030}
}
Kostenlos starten →