EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Objective Optimization of a High-Temperature Flange–Bolt–Gasket System Based on a Cyclic Symmetric Thermal–Structural Coupling Model

Honghao Xu, Peigang Jiao, Changhui Zheng, Jiaxin Shi, Yiheng Zhang

Symmetry · 23.07.2026 · 18 (8) · 1252

DOI: 10.3390/sym18081252 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Symmetry, online erschienen am 23.07.2026. Verfasst von Honghao Xu und 4 weiteren Autor:innen. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Shandong Provincial Key Research and Development Program, Shandong Provincial Department of Transportation Science and Technology Program, Shandong Provincial Transportation Science and Technology Program.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The high-temperature sealing reliability of flange–bolt–gasket systems is governed by the coupled gasket leakage, flange cracking, and bolt yielding. This study investigates a DN200 PN40 (nominal diameter 200 mm and nominal pressure 4.0 MPa) weld-neck flange assembly operating under 300 °C superheated steam at 4 MPa internal pressure. Exploiting the assembly’s 12-fold cyclic rotational symmetry, a 1/12 periodic-sector finite element model with steady-state thermal–structural sequential coupling was developed in ANSYS Workbench and validated against the Omiya–Sawa 3-inch weld-neck flange benchmark at two levels (Level 1: bolt load vs. experiment; Level 2: 250 °C gasket contact pressure vs. reference finite element method (FEM)), with maximum errors below 1.5% in both levels; the benchmark thus establishes the reliability of the modeling procedure rather than constituting a direct experimental validation of the DN200 PN40 configuration. Using a central composite design, second-order response surface models (RSM) and Kriging surrogate models were constructed and compared, followed by Sobol global sensitivity analysis, multi-objective optimization using the non-dominated sorting genetic algorithm II (NSGA-II), and decision-making using the technique for order preference by similarity to ideal solution (TOPSIS), with bolt preload F and gasket width b as design variables. Baseline analysis revealed a differential contact pressure distribution—lower at the inner radius and higher at the outer radius—driven by a −0.308° flange rotation, identifying the inner gasket edge as the critical sealing failure path. RSM outperformed Kriging for the primary objective (mean absolute percentage error (MAPE): 0.72% vs. 3.61%), and the Pareto front collapsed to b = 19 mm. The TOPSIS-recommended optimum (F = 59,942 N, b = 19.00 mm), verified by ANSYS back-substitution, increased the minimum gasket contact pressure by 31.01% while reducing the flange membrane-plus-bending stress by 2.26%, achieving a coordinated improvement of both sealing performance and structural safety.

Förderung

  • Shandong Provincial Key Research and Development Program
  • Shandong Provincial Department of Transportation Science and Technology Program
  • Shandong Provincial Transportation Science and Technology Program

Zitieren

APA

Xu, H., Jiao, P., Zheng, C., Shi, J., & Zhang, Y. (2026). Multi-Objective Optimization of a High-Temperature Flange–Bolt–Gasket System Based on a Cyclic Symmetric Thermal–Structural Coupling Model. Symmetry, 18(8), 1252. https://doi.org/10.3390/sym18081252

Vancouver

Xu H, Jiao P, Zheng C, Shi J, Zhang Y. Multi-Objective Optimization of a High-Temperature Flange–Bolt–Gasket System Based on a Cyclic Symmetric Thermal–Structural Coupling Model. Symmetry. 2026;18(8):1252. doi:10.3390/sym18081252

BibTeX
@article{Xu2026,
  author = {Xu, Honghao and Jiao, Peigang and Zheng, Changhui and Shi, Jiaxin and Zhang, Yiheng},
  title = {Multi-Objective Optimization of a High-Temperature Flange–Bolt–Gasket System Based on a Cyclic Symmetric Thermal–Structural Coupling Model},
  journal = {Symmetry},
  year = {2026},
  volume = {18},
  number = {8},
  pages = {1252},
  doi = {10.3390/sym18081252}
}
Kostenlos starten →