Research into Energy-Saving Control Strategies of a Bulldozer Driven by a Torque Converter Based on the Minimum Fuel Consumption Rate of the Whole Machine
Sustainability · 20.11.2024 · 16 (22) · 10111
DOI: 10.3390/su162210111 ↗Kurz gefasst
Fachartikel in der Zeitschrift Sustainability, online erschienen am 20.11.2024. Verfasst von Hongbin Qiang und 5 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Youth program of the National Natural Science Foundation of China, Natural Science Foundation of the Jiangsu Higher Education Institutions of China, Changzhou Leading Innovative Talents Introduction and Cultivation Project.
Abstract (Originalsprache)
In order to address the issue of poor fuel efficiency in hydraulic bulldozers during operation, this paper proposes a speed–load control strategy aimed at minimizing the overall fuel consumption rate of the machine. First, input–output models of the engine, hydraulic torque converter and the entire vehicle were established. Then, based on the bulldozer’s output power and fuel consumption rate, a performance metric for the overall fuel consumption rate was proposed to reflect the machine’s working efficiency. The characteristics of the overall fuel consumption rate were analyzed under different load, speed, and gear conditions. Next, a work point optimization control strategy was proposed for the whole machine energy-saving mode and constant power mode, aiming to minimize the overall fuel consumption rate while using the load, speed, and gear as control variables. To verify the feasibility of the work point optimization control strategy, simulations were conducted for both the energy-saving and constant power modes. The simulation results showed that in the whole machine energy-saving mode, this control strategy resulted in the lowest fuel consumption compared to constant speed control strategies at 1500, 1700, and 2000 rpm, with significant reductions in most cases. In the constant power mode, a comparison between four optimal operating points and the whole machine energy-saving mode revealed that while the former had slightly higher fuel consumption, it ensured a stable power output. Finally, experimental testing demonstrated that the proposed control strategy reduced the overall fuel consumption rate by 12.5% compared to the constant speed mode, verifying the effectiveness of the strategy. The study concludes that the energy-saving control strategy, through the coordinated switching between the two modes in complex operating conditions, not only ensures a stable power output for the bulldozer but also significantly improves fuel efficiency, providing an important reference for optimizing the efficiency of transmission systems in construction machines.
Förderung
- Youth program of the National Natural Science Foundation of China
- Natural Science Foundation of the Jiangsu Higher Education Institutions of China
- Changzhou Leading Innovative Talents Introduction and Cultivation Project
- Jiangsu University of Technology Graduate Practice Innovation Program
Zitieren
APA
Qiang, H., Li, H., Kang, S., Liu, K., Yang, J., & Wang, L. (2024). Research into Energy-Saving Control Strategies of a Bulldozer Driven by a Torque Converter Based on the Minimum Fuel Consumption Rate of the Whole Machine. Sustainability, 16(22), 10111. https://doi.org/10.3390/su162210111
Vancouver
Qiang H, Li H, Kang S, Liu K, Yang J, Wang L. Research into Energy-Saving Control Strategies of a Bulldozer Driven by a Torque Converter Based on the Minimum Fuel Consumption Rate of the Whole Machine. Sustainability. 2024;16(22):10111. doi:10.3390/su162210111
BibTeX
@article{Qiang2024,
author = {Qiang, Hongbin and Li, He and Kang, Shaopeng and Liu, Kailei and Yang, Jing and Wang, Lian},
title = {Research into Energy-Saving Control Strategies of a Bulldozer Driven by a Torque Converter Based on the Minimum Fuel Consumption Rate of the Whole Machine},
journal = {Sustainability},
year = {2024},
volume = {16},
number = {22},
pages = {10111},
doi = {10.3390/su162210111}
}
EUVIMED