EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Characterization of Bio-Epoxy Composites with Mussel Shell Powder and Posidonia Fibers

Sara Mattiello, Mattia Latini, Greta Vicentini, Chiara Giosuè, Danilo Nikolic, Cristiano Fragassa, Valeria Corinaldesi, Mattia Merlin, Carlo Santulli

Sci · 10.02.2026 · 8 (2) · 41

DOI: 10.3390/sci8020041 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sci, online erschienen am 10.02.2026. Verfasst von Sara Mattiello und 8 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Foreign Affairs and International Cooperation of Italy, Ministry of Education, Science, Culture and Sports of Montenegro.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bio-epoxy composites were fabricated by casting a resin–hardener–filler mixture into 3D-printed molds, using different sea-originated secondary raw materials: mussel shell powder (MSP) (63–83 μm) and Posidonia oceanica short fibers (POF) (1–2 mm). Monofiller composites were prepared with 5 or 10 wt.% MSP, or 5 or 10 wt.% POF. Hybrid formulations were also produced, containing both MSP and POF in two combinations, where the total amount of filler again summed up at 10 wt.%. A subset of the samples was conditioned by immersion in a 35 ‰ NaCl solution reproducing seawater composition until saturation was reached. Characterization was carried out on unconditioned and conditioned samples by Shore D hardness and Charpy impact tests while performing three-point flexural loading only on unconditioned ones. Fracture morphology was also investigated. Adding MSP slightly enhanced resin hardness, whereas impact absorption exhibited, to a variable extent, a two-phase behavior, reproducing crack initiation and propagation. The MSP6-POF4 hybrid configuration provided the greatest improvement in absorbed energy (25–30% higher), which was retained after conditioning. The introduction of fillers, first separately, then in combination, resulted in a reduction in flexural strength to a similar extent for all unconditioned configurations. Finally, composite panels containing 10 wt.% MSP, 10 wt.% POF, and a 6MSP–4POF hybrid formulation, intended for prospective boat deck applications, were fabricated and compared with neat bio-epoxy, showing satisfactory consolidation. Density and post-molding dimensional shrinkage were measured on the panels.

Förderung

  • Ministry of Foreign Affairs and International Cooperation of Italy
  • Ministry of Education, Science, Culture and Sports of Montenegro

Zitieren

APA

Mattiello, S., Latini, M., Vicentini, G., Giosuè, C., Nikolic, D., Fragassa, C., Corinaldesi, V., Merlin, M., & Santulli, C. (2026). Characterization of Bio-Epoxy Composites with Mussel Shell Powder and Posidonia Fibers. Sci, 8(2), 41. https://doi.org/10.3390/sci8020041

Vancouver

Mattiello S, Latini M, Vicentini G, Giosuè C, Nikolic D, Fragassa C, et al. Characterization of Bio-Epoxy Composites with Mussel Shell Powder and Posidonia Fibers. Sci. 2026;8(2):41. doi:10.3390/sci8020041

BibTeX
@article{Mattiello2026,
  author = {Mattiello, Sara and Latini, Mattia and Vicentini, Greta and Giosuè, Chiara and Nikolic, Danilo and Fragassa, Cristiano and Corinaldesi, Valeria and Merlin, Mattia and Santulli, Carlo},
  title = {Characterization of Bio-Epoxy Composites with Mussel Shell Powder and Posidonia Fibers},
  journal = {Sci},
  year = {2026},
  volume = {8},
  number = {2},
  pages = {41},
  doi = {10.3390/sci8020041}
}
Kostenlos starten →