EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Identification Method for Seated Balance Control Based on Horizontal Support-Surface Sway and Dual Force-Platform Measurements

Mohamed Elsaroukh iD, Motomichi Sonobe iD, Tsukasa Okaji iD

Sensors · 2026

DOI: 10.3390/s26196007 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, 2026. Verfasst von Mohamed Elsaroukh und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Intelligent Mechanical Systems Engineering, Kochi University of Technology, 185 Miyanokuchi, Tosayamada, Kami, Kochi 782-8502, Japan. Hauptthemen laut MEDLINE: Postural Balance, Sitting Position. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Japan Society for the Promotion of Science, JSPS KAKENHI.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Identifying seated balance control may contribute to estimation of time delay and evaluation of vestibular weighting. However, few practical methods exist for measuring seated body motion or identifying seated balance control. This study aimed to estimate upper-body center of mass (COM) displacement during sitting under horizontal sway of the support surface using a practical measurement method and to identify a seated balance control system for each individual. Two force platforms under the buttocks and feet were synchronized with a support surface accelerometer. Under unpredictable horizontal perturbations composed of a multi-cosine waveform below 1.50 Hz, balance control was identified in an eyes-closed condition using a parametric model incorporating delayed COM state feedback and horizontal head acceleration feedback, the latter representing otolith-mediated detection of horizontal head acceleration. When validated against an optical motion capture system (five participants), the identified parameters exhibited an average relative error of less than 5%. A two-day reproducibility test (25 participants) yielded intraclass correlation coefficients (ICC(1,1)) of the four identified parameters ranging from 0.57 to 0.73, indicating moderate reliability. The identified head acceleration feedback gain may indicate head acceleration sensitivity, even among healthy adults.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Postural BalanceSitting PositionHumansAccelerationAdultFemaleBiomechanical PhenomenaReproducibility of ResultsPostureMotion Capture

Stichwörter der Autor:innen

balance identificationcenter of massforce platformhead acceleration feedbackseated posturetime delay

Autor:innen und Institutionen

  • Department of Intelligent Mechanical Systems Engineering, Kochi University of Technology, 185 Miyanokuchi, Tosayamada, Kami, Kochi 782-8502, Japan.
  • Faculty of Engineering, Menoufia University, Shebin El-Kom 32511, Egypt.

ORCID-Profile: Mohamed Elsaroukh, Motomichi Sonobe, Tsukasa Okaji

Förderung

  • Japan Society for the Promotion of Science
  • JSPS KAKENHI

Zitieren

APA

Elsaroukh, M., Sonobe, M., & Okaji, T. (2026). Identification Method for Seated Balance Control Based on Horizontal Support-Surface Sway and Dual Force-Platform Measurements. Sensors. https://doi.org/10.3390/s26196007

Vancouver

Elsaroukh M, Sonobe M, Okaji T. Identification Method for Seated Balance Control Based on Horizontal Support-Surface Sway and Dual Force-Platform Measurements. Sensors. 2026. doi:10.3390/s26196007

BibTeX
@article{Elsaroukh2026,
  author = {Elsaroukh, Mohamed and Sonobe, Motomichi and Okaji, Tsukasa},
  title = {Identification Method for Seated Balance Control Based on Horizontal Support-Surface Sway and Dual Force-Platform Measurements},
  journal = {Sensors},
  year = {2026},
  doi = {10.3390/s26196007}
}
Kostenlos starten →