EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Enhanced Absolute Eddy Current Probe for Surface Cracks Detection at High Temperatures

Zhiying Liu, Wenze Shi, Chao Lu, Tuan Zhu iD, Hongyu Sun iD, Zhonghao Luo, Gongpeng Yang, Yiping Liang

Sensors · 26.06.2026 · 26 (13) · 4056

DOI: 10.3390/s26134056 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 26.06.2026. Verfasst von Zhiying Liu und 7 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory of Non-Destructive Testing, Ministry of Education, Nanchang Hangkong University, Nanchang 330063, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Laboratory Technology Basic Research Projects, Key Laboratory of Nondestructive Testing (Nanchang Hangkong University), Ministry of Education.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Non-destructive evaluation of surface cracks in Inconel 718 nickel-based alloys operating at high temperatures is crucial for monitoring aero-engine hot-section components. Conventional eddy current testing is often constrained by thermal core degradation and low signal-to-noise ratios, struggling to meet detection requirements in such extreme environments. To address this, this study proposes an optimized absolute probe integrated with an efficient water-cooling system. A multi-physics finite element model was developed to optimize the probe design, focusing on key parameters such as excitation frequency and the geometric dimensions of the coil and ferrite core. Experimental results demonstrate that the optimized probe significantly enhances detection sensitivity over conventional models. Specifically, the peak amplitude increased by 76.2% and the signal-to-noise improved by nearly 10 dB for a 0.3 mm-deep crack. In practical applications, the probe achieves high-sensitivity detection of a 0.3 mm-deep crack at 500 °C. At 600 °C, it reliably detects a 0.5 mm-deep crack with a coefficient of variation not exceeding 3.5% and it retains detection capabilities even at 650 °C. Therefore, this sensor design strategy proves to be a highly viable method for non-destructive evaluation in extreme industrial thermal environments.

Schlagwörter

Stichwörter der Autor:innen

high-temperature eddy current testingnickel-based alloyoptimal designsurface crackswater-cooled sensor

Autor:innen und Institutionen

  • Key Laboratory of Non-Destructive Testing, Ministry of Education, Nanchang Hangkong University, Nanchang 330063, China.
  • School of Physical Science and Engineering, Beijing Jiaotong University, Beijing 100044, China.
  • Intelligent Non-Destructive Testing Center, Taihang National Laboratory, Nanchang 330096, China.

ORCID-Profile: Tuan Zhu, Hongyu Sun

Förderung

  • National Laboratory Technology Basic Research Projects
  • Key Laboratory of Nondestructive Testing (Nanchang Hangkong University), Ministry of Education

Zitieren

APA

Liu, Z., Shi, W., Lu, C., Zhu, T., Sun, H., Luo, Z., Yang, G., & Liang, Y. (2026). An Enhanced Absolute Eddy Current Probe for Surface Cracks Detection at High Temperatures. Sensors, 26(13), 4056. https://doi.org/10.3390/s26134056

Vancouver

Liu Z, Shi W, Lu C, Zhu T, Sun H, Luo Z, et al. An Enhanced Absolute Eddy Current Probe for Surface Cracks Detection at High Temperatures. Sensors. 2026;26(13):4056. doi:10.3390/s26134056

BibTeX
@article{Liu2026,
  author = {Liu, Zhiying and Shi, Wenze and Lu, Chao and Zhu, Tuan and Sun, Hongyu and Luo, Zhonghao and Yang, Gongpeng and Liang, Yiping},
  title = {An Enhanced Absolute Eddy Current Probe for Surface Cracks Detection at High Temperatures},
  journal = {Sensors},
  year = {2026},
  volume = {26},
  number = {13},
  pages = {4056},
  doi = {10.3390/s26134056}
}
Kostenlos starten →