Design Principles for EMAT Coils Based on Lorentz Force
Sensors · 06.06.2026 · 26 (12) · 3624
DOI: 10.3390/s26123624 ↗Kurz gefasst
Fachartikel in der Zeitschrift Sensors, online erschienen am 06.06.2026. Verfasst von Jhon Padilla und 6 weiteren Autor:innen. Beteiligte Einrichtung: Corporación para la Investigación de la Corrosión, Piedecuesta 681011, Colombia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Wellcome Trust, MINISTERIO DE CIENCIA Y TECNOLOGÍA DE COLOMBIA.
Abstract (Originalsprache)
EMAT technology for Non Destructive testing is an important method for materials testing in several industries. In EMAT tools, a key issue is the EMAT coils design and implementation. Depending on the type of inspection, the coil type should be selected, and then, its dimensions should be calculated. This paper describes a methodology to select, design and implement EMAT coils based on Lorentz Force for applications such as thickness measurement and crack detection. Unlike previous works that focus on a single coil topology, this study integrates coil selection, dimensional design, COMSOL-based radiation-pattern simulation and experimental validation within a single workflow. Four Lorentz-force coil designs are covered: PCB spiral (CSPCB), 3D-printed spiral (CS3D), PCB meander-line (CMPCB) and 3D-printed meander-line (CM3D). Key design parameters are explicitly addressed: number of turns N, outer and inner radii R and r0, track width w and spacing s for spiral coils, and meander length and inter-trace distance for meander-line coils. Simulation verification is performed in COMSOL Multiphysics by evaluating the von Mises stress along a semicircular path around the coil to obtain the angular radiation pattern. Experimentally, polar radiation patterns are measured at 500 kHz, 1.9 MHz and 4 MHz on a steel specimen, matching the simulation frequencies, with maximum amplitudes of 32.2, 46.4, 47.9 and 10.6 mV for CSPCB, CS3D, CMPCB and CM3D, respectively, showing consistent agreement between simulated and measured lobe shape and directivity. This work also uses an analogy with radio frequency antennas to better understand the operation of coils through the concept of radiation patterns, in this case in solid materials such as steel.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Corporación para la Investigación de la Corrosión, Piedecuesta 681011, Colombia.
- Universidad Pontificia Bolivariana, Medellin 050031, Colombia.
- Fundación Universitaria de San Gil, San Gil 684031, Colombia.
ORCID-Profile: Jhon Padilla, Daniel Bernal, Mauricio Barrios Castellanos, Miguel Rios, Juan Argüello, Juan Mantilla, Luis Angel
Förderung
- Wellcome Trust
- MINISTERIO DE CIENCIA Y TECNOLOGÍA DE COLOMBIA
Zitieren
APA
Padilla, J., Bernal, D., Castellanos, M. B., Rios, M., Argüello, J., Mantilla, J., & Angel, L. (2026). Design Principles for EMAT Coils Based on Lorentz Force. Sensors, 26(12), 3624. https://doi.org/10.3390/s26123624
Vancouver
Padilla J, Bernal D, Castellanos MB, Rios M, Argüello J, Mantilla J, et al. Design Principles for EMAT Coils Based on Lorentz Force. Sensors. 2026;26(12):3624. doi:10.3390/s26123624
BibTeX
@article{Padilla2026,
author = {Padilla, Jhon and Bernal, Daniel and Castellanos, Mauricio Barrios and Rios, Miguel and Argüello, Juan and Mantilla, Juan and Angel, Luis},
title = {Design Principles for EMAT Coils Based on Lorentz Force},
journal = {Sensors},
year = {2026},
volume = {26},
number = {12},
pages = {3624},
doi = {10.3390/s26123624}
}
EUVIMED