Cross-Contamination Identification of Additive Manufacturing Metal Powders Using Spatially Confined Particle-Flow LIBS and Machine Learning
Sensors · 06.06.2026 · 26 (12) · 3591
DOI: 10.3390/s26123591 ↗Kurz gefasst
Fachartikel in der Zeitschrift Sensors, online erschienen am 06.06.2026. Verfasst von Leiyi Ding und 5 weiteren Autor:innen. Beteiligte Einrichtung: Analytical & Testing Center, School of Mechanical Engineering, Northwestern Polytechnical University, Xi'an 710072, China. Die Arbeit nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Major Project, National Key Research and Development Program of China, Fundamental Research Funds for the Central Universities.
Abstract (Originalsprache)
Laser-induced breakdown spectroscopy (LIBS) offers rapid, in situ, and multi-element detection, and therefore shows strong potential for quality monitoring of metal powders in additive manufacturing. However, direct LIBS analysis of flowing metal powders is often affected by particle splashing, unstable laser–particle coupling, and plasma fluctuations, which reduce signal repeatability and detection reliability. To address these issues, this study developed an integrated measurement and classification framework for identifying cross-contamination in additive-manufacturing metal powders. A stable powder particle stream was generated through vibratory feeding and particle-flow focusing, while a hollow quartz tube with a side opening was introduced to provide cylindrical spatial confinement, thereby improving the stability of laser–particle interaction and enabling in situ spectral acquisition without pellet preparation. TC4 powder was used as the base material and AlSi10Mg powder as the contaminant, and samples with contamination levels of 0, 0.5, 1, 2, and 5 wt.% were prepared. Two independent batches of single-shot LIBS spectra were collected. To reduce the influence of strong spectral fluctuations, outlier spectra were removed using full-spectrum total-intensity quantile filtering, followed by asymmetric least-squares baseline correction and standard normal variate transformation. PCA combined with multiple machine-learning models was then applied for contamination identification. The results showed that LIBS spectra at different contamination levels exhibited distinguishable distributions in principal-component space, and the spectral differences between clean and contaminated powders became more pronounced with increasing contamination level. In binary classification, several models achieved high classification accuracy at medium and high contamination levels, while PCA-SVM-RBF showed the best performance at low concentrations. In five-class cross-validation, the 5 wt.% class exhibited the clearest decision boundary, whereas confusion remained among low and adjacent contamination levels, indicating that contamination-induced spectral responses followed a more continuous transition. These results demonstrate that the proposed spatially confined particle-flow LIBS framework combined with machine-learning classification can effectively achieve rapid identification of cross-contamination in additive-manufacturing metal powders and provides a feasible technical route for online powder quality monitoring.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Analytical & Testing Center, School of Mechanical Engineering, Northwestern Polytechnical University, Xi'an 710072, China.
- Shenzhen Research Institute, Northwestern Polytechnical University, Shenzhen 518057, China.
ORCID-Profile: Yuanbin Wang
Förderung
- National Science and Technology Major Project
- National Key Research and Development Program of China
- Fundamental Research Funds for the Central Universities
- Natural Science Foundation of Shaanxi Province
- National Natural Science Foundation of China
- Guangdong Basic and Applied Basic Research Foundation
- Science Fund Program for Excellent Young Scientists
Zitieren
APA
Ding, L., Feng, D., Wang, Y., Shan, M., Wang, Y., & Ma, N. (2026). Cross-Contamination Identification of Additive Manufacturing Metal Powders Using Spatially Confined Particle-Flow LIBS and Machine Learning. Sensors, 26(12), 3591. https://doi.org/10.3390/s26123591
Vancouver
Ding L, Feng D, Wang Y, Shan M, Wang Y, Ma N. Cross-Contamination Identification of Additive Manufacturing Metal Powders Using Spatially Confined Particle-Flow LIBS and Machine Learning. Sensors. 2026;26(12):3591. doi:10.3390/s26123591
BibTeX
@article{Ding2026,
author = {Ding, Leiyi and Feng, Dan and Wang, Yinghao and Shan, Mengjie and Wang, Yuanbin and Ma, Nan},
title = {Cross-Contamination Identification of Additive Manufacturing Metal Powders Using Spatially Confined Particle-Flow LIBS and Machine Learning},
journal = {Sensors},
year = {2026},
volume = {26},
number = {12},
pages = {3591},
doi = {10.3390/s26123591}
}
EUVIMED