EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Piezoresistive Sensing Performance of Smart Layer in Multi-Material 3D-Printed Reinforced Cementitious Beams

Han Liu iD, Israel Sousa iD, Shelby E Doyle iD, Antonella D'Alessandro iD, Filippo Ubertini iD, Simon Laflamme iD

Sensors · 19.05.2026 · 26 (10) · 3204

DOI: 10.3390/s26103204 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 19.05.2026. Verfasst von Han Liu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil, Construction, and Environmental Engineering, Iowa State University, Ames, IA 50010, USA. Die Arbeit nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: U.S. National Science Foundation, Ministry of Universities and Research, National Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

3D concrete printing (3DP) enables automated construction with reduced material waste and enhanced geometric flexibility. However, its structural performance remains sensitive to anisotropy, mix design, and printing parameters, thereby complicating quality control. Self-sensing cementitious materials provide a promising approach by enabling intrinsic strain monitoring during fabrication and service. In this study, a hybrid multi-material printing strategy was developed using a conductive cement-based mix incorporating graphite (G), milled carbon microfibers (MCMF), and chopped carbon microfibers (CCMF), alongside a plain cement-based matrix. Based on percolation analysis, an optimal composition of 2 wt.% G, 0.25 wt.% MCMF, and 0.0625 wt.% CCMF was selected. Reinforced beam specimens were fabricated with the conductive material embedded in either the tensile (bottom) or compressive (top) region, combined with two internal architectures: diagonal infill and solid-base configuration. Four configurations were defined: Pattern 1 (bottom/diagonal), Pattern 2 (bottom/solid-base), Pattern 3 (top/diagonal), and Pattern 4 (top/solid-base). Cyclic three-point bending tests with spatially distributed electrical measurements were conducted to evaluate the electromechanical response in the elastic range. Specimens with the conductive layer located in the tensile region (Patterns 1 and 2) consistently exhibited higher gauge factors than those in the compressive region (Patterns 3 and 4). Pattern 2 exhibited the best sensing performance, with an average gauge factor of 556 and SNR of 31. Across all configurations, SNR decreased with increasing electrode spacing, with reductions of up to 31.0%, demonstrating the effect of current path length on sensing performance.

Schlagwörter

Stichwörter der Autor:innen

3D printed concretehybrid printingpiezoresistive propertiesself-sensingsmart concretestructural health monitoring

Autor:innen und Institutionen

  • Department of Civil, Construction, and Environmental Engineering, Iowa State University, Ames, IA 50010, USA.
  • Department of Civil and Environmental Engineering, University of Perugia, Via G. Duranti, 93, 06125 Perugia, Italy.
  • Department of Architecture, Iowa State University, Ames, IA 50010, USA.
  • Department of Electrical and Computer Engineering, Iowa State University, Ames, IA 50010, USA.

ORCID-Profile: Han Liu, Israel Sousa, Shelby E Doyle, Antonella D'Alessandro, Filippo Ubertini, Simon Laflamme

Förderung

  • U.S. National Science Foundation
  • Ministry of Universities and Research
  • National Science Foundation
  • Italian Ministry of University and Research

Zitieren

APA

Liu, H., Sousa, I., Doyle, S. E., D'Alessandro, A., Ubertini, F., & Laflamme, S. (2026). Piezoresistive Sensing Performance of Smart Layer in Multi-Material 3D-Printed Reinforced Cementitious Beams. Sensors, 26(10), 3204. https://doi.org/10.3390/s26103204

Vancouver

Liu H, Sousa I, Doyle SE, D'Alessandro A, Ubertini F, Laflamme S. Piezoresistive Sensing Performance of Smart Layer in Multi-Material 3D-Printed Reinforced Cementitious Beams. Sensors. 2026;26(10):3204. doi:10.3390/s26103204

BibTeX
@article{Liu2026,
  author = {Liu, Han and Sousa, Israel and Doyle, Shelby E and D'Alessandro, Antonella and Ubertini, Filippo and Laflamme, Simon},
  title = {Piezoresistive Sensing Performance of Smart Layer in Multi-Material 3D-Printed Reinforced Cementitious Beams},
  journal = {Sensors},
  year = {2026},
  volume = {26},
  number = {10},
  pages = {3204},
  doi = {10.3390/s26103204}
}
Kostenlos starten →