EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Strain Monitoring of Vertical Axis Wind Turbine Tower Using Fiber Bragg Gratings

Bastien Van Esbeen iD, Valentin Manto, Damien Kinet, Corentin Guyot iD, Christophe Caucheteur

Sensors · 24.06.2025 · 25 (13) · 3921

DOI: 10.3390/s25133921 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 24.06.2025. Verfasst von Bastien Van Esbeen und 4 weiteren Autor:innen. Beteiligte Einrichtung: Advanced Photonic Sensors Unit, University of Mons, 31 Boulevard Dolez, 7000 Mons, Belgium. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: F.R.S.-FNRS, Région Wallonne, Walloon Region.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This article presents the findings of an experimental study conducted on a vertical axis wind turbine (VAWT) tower instrumented with cascaded fiber Bragg grating (FBG) sensors to detect bending deformations. Structural health monitoring (SHM) is an essential need in the industry to reduce costs and maintenance time, and to prevent machine failures. First, FBG strain sensors were glued vertically along the tower to investigate the sensors behavior as a function of their height. The maximum signal-to-noise ratio is obtained when FBGs are placed at the tower base. Then, four packages were installed inside the tower, at the base, according to four cardinal directions. Each package contains an FBG strain sensor, and an extra temperature FBG for discrimination. The use of easy-to-deploy packages is a must for industrial installations. Afterwards, by using power spectral density (PSD) on the strain signals, three sources of tower oscillations are discovered: wind force, structure unbalance, and 1st tower mode resonance, each with its intrinsic frequency. Wind force and structure unbalance cause mechanical stresses at a frequency proportional to the wind turbine rotational speed, while the 1st tower mode frequency depends only on the machine geometry, regardless of the rotational speed. This study also analyzes the deformation amplitude for different rotational rates within the VAWT operational range (10–35 rpm). The resonance amplitude depends on the proximity of the rotational rate to the resonant frequency (22 rpm) and the duration at that rate. For structure unbalance, the oscillation amplitude increases with the rotational rate, due to the centrifugal effect. It is supposed that wind force deformation amplitude naturally depends on wind speed, which is unpredictable at a given precise time. The results of our experimental observations are very valuable for both the wind turbine manufacturer and owner.

Schlagwörter

Stichwörter der Autor:innen

VAWT monitoringfiber Bragg gratingsfiber optic sensorstructural health monitoringtower bending

Autor:innen und Institutionen

  • Advanced Photonic Sensors Unit, University of Mons, 31 Boulevard Dolez, 7000 Mons, Belgium.
  • Fairwind s.a., 299 Chaussée de Gilly, 6220 Fleurus, Belgium.
  • B-SENS SRL, 31 Boulevard Dolez, 7000 Mons, Belgium.

ORCID-Profile: Bastien Van Esbeen, Corentin Guyot

Förderung

  • F.R.S.-FNRS
  • Région Wallonne
  • Walloon Region

Zitieren

APA

Van Esbeen, B., Manto, V., Kinet, D., Guyot, C., & Caucheteur, C. (2025). Strain Monitoring of Vertical Axis Wind Turbine Tower Using Fiber Bragg Gratings. Sensors, 25(13), 3921. https://doi.org/10.3390/s25133921

Vancouver

Van Esbeen B, Manto V, Kinet D, Guyot C, Caucheteur C. Strain Monitoring of Vertical Axis Wind Turbine Tower Using Fiber Bragg Gratings. Sensors. 2025;25(13):3921. doi:10.3390/s25133921

BibTeX
@article{VanEsbeen2025,
  author = {Van Esbeen, Bastien and Manto, Valentin and Kinet, Damien and Guyot, Corentin and Caucheteur, Christophe},
  title = {Strain Monitoring of Vertical Axis Wind Turbine Tower Using Fiber Bragg Gratings},
  journal = {Sensors},
  year = {2025},
  volume = {25},
  number = {13},
  pages = {3921},
  doi = {10.3390/s25133921}
}
Kostenlos starten →