Pressure-Driven Piezoelectric Sensors and Energy Harvesting in Biaxially Oriented Polyethylene Terephthalate Film
Sensors · 17.02.2024 · 24 (4) · 1275
DOI: 10.3390/s24041275 ↗Kurz gefasst
Fachartikel in der Zeitschrift Sensors, online erschienen am 17.02.2024. Verfasst von Romana Stepancikova und 5 weiteren Autor:innen. Beteiligte Einrichtung: Centre of Polymer Systems, University Institute, Tomas Bata University, Trida T. Bati 5678, 76001 Zlin, Czech Republic. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Ministry of Education, Youth, and Sports of the Czech Republic within the framework of DKRVO.
Abstract (Originalsprache)
This study reports the possibility of using biaxially oriented polyethylene terephthalate (BOPET) plastic packaging to convert mechanical energy into electrical energy. Electricity is generated due to the piezoelectricity of BOPET. Electricity generation depends on the mechanical deformation of the processing aids (inorganic crystals), which were found and identified by SEM and EDAX analyses as SiO2. BOPET, as an electron source, was assembled and tested as an energy conversion and self-powered mechanical stimuli sensor using potential applications in wearable electronics. When a pressure pulse after pendulum impact with a maximum stress of 926 kPa and an impact velocity of 2.1 m/s was applied, a voltage of 60 V was generated with short-circuit current and charge densities of 15 μAcm−2 and 138 nCm−2, respectively. Due to the orientation and stress-induced crystallization of polymer chains, BOPET films acquire very good mechanical properties, which are not lost during their primary usage as packaging materials and are beneficial for the durability of the sensors. The signals detected using BOPET sensors derived from pendulum impact and sieve analyses were also harvested for up to 80 cycles and up to 40 s with short-circuit voltages of 107 V and 95 V, respectively. In addition to their low price, the advantage of sensors made from BOPET plastic packaging waste lies in their chemical resistance and stability under exposure to oxygen, ultraviolet light, and moisture.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Centre of Polymer Systems, University Institute, Tomas Bata University, Trida T. Bati 5678, 76001 Zlin, Czech Republic.
- Department of Production Engineering, Faculty of Technology, Tomas Bata University in Zlin, Vavreckova 5669, 76001 Zlin, Czech Republic.
- Department of Physics and Materials Engineering, Tomas Bata University in Zlin, Vavreckova 5669, 76001 Zlin, Czech Republic.
ORCID-Profile: Romana Stepancikova, Jiri Matyas, Milan Masar, Berenika Hausnerova, Petr Slobodian
Förderung
- the Ministry of Education, Youth, and Sports of the Czech Republic within the framework of DKRVO
Zitieren
APA
Stepancikova, R., Olejnik, R., Matyas, J., Masar, M., Hausnerova, B., & Slobodian, P. (2024). Pressure-Driven Piezoelectric Sensors and Energy Harvesting in Biaxially Oriented Polyethylene Terephthalate Film. Sensors, 24(4), 1275. https://doi.org/10.3390/s24041275
Vancouver
Stepancikova R, Olejnik R, Matyas J, Masar M, Hausnerova B, Slobodian P. Pressure-Driven Piezoelectric Sensors and Energy Harvesting in Biaxially Oriented Polyethylene Terephthalate Film. Sensors. 2024;24(4):1275. doi:10.3390/s24041275
BibTeX
@article{Stepancikova2024,
author = {Stepancikova, Romana and Olejnik, Robert and Matyas, Jiri and Masar, Milan and Hausnerova, Berenika and Slobodian, Petr},
title = {Pressure-Driven Piezoelectric Sensors and Energy Harvesting in Biaxially Oriented Polyethylene Terephthalate Film},
journal = {Sensors},
year = {2024},
volume = {24},
number = {4},
pages = {1275},
doi = {10.3390/s24041275}
}
EUVIMED