EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Measurement of Cutting Temperature in Interrupted Machining Using Optical Spectrometry

Isaí Espinoza-Torres iD, Israel Martínez-Ramírez iD, Juan Manuel Sierra-Hernández, Daniel Jauregui-Vazquez iD, Miguel Ernesto Gutiérrez-Rivera iD, Felipe de Jesús Torres-Del Carmen iD, Tania Lozano-Hernández iD

Sensors · 04.11.2023 · 23 (21) · 8968

DOI: 10.3390/s23218968 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 04.11.2023. Verfasst von Isaí Espinoza-Torres und 6 weiteren Autor:innen. Beteiligte Einrichtung: Departamento de Ingeniería Mecánica, División de Ingenierías, Campus Irapuato-Salamanca, Universidad de Guanajuato, Carretera Salamanca-Valle de Sant…. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidad de Guanajuato, CONAHCYT and PRODEP.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This research presents an experimental study focused on measuring temperature at the tool flank during the up-milling process at high cutting speed. The proposed system deals with emissivity compensation through a two-photodetector system and during calibration. A ratio pyrometer composed of two photodetectors and a multimode fiber-optic coupler is employed to capture the radiation emitted by the cutting insert. The pyrometer is calibrated using an innovative calibration system that addresses theoretical discrepancies arising from various factors affecting the measurement of cutting temperature. This calibration system replicates the milling process to generate a calibration curve. Experimentally, AISI 4140 steel is machined with coated tungsten carbide inserts, using cutting speeds of 300 and 400 m/min, and feed rates of 0.08 and 0.16 mm/tooth. The results reveal a maximum recorded cutting temperature of 518 °C and a minimum of 304 °C. The cutting temperature tends to increase with higher cutting speeds and feed rates, with cutting speed being the more influential factor in this increase. Both the pyrometer calibration and experimental outcomes yield satisfactory results. Finally, the results showed that the process and the device prove to be a convenient, effective, and precise method of measuring cutting temperature in machine processes.

Schlagwörter

Stichwörter der Autor:innen

calibration systemcutting temperaturemillingratio pyrometer

Autor:innen und Institutionen

  • Departamento de Ingeniería Mecánica, División de Ingenierías, Campus Irapuato-Salamanca, Universidad de Guanajuato, Carretera Salamanca-Valle de Santiago km 3.5+1.8, Comunidad de Palo Blanco, Salamanca 36885, Mexico.
  • Departamento de Ingeniería Electrónica, División de Ingenierías, Campus Irapuato-Salamanca, Universidad de Guanajuato, Carretera Salamanca-Valle de Santiago km 3.5+1.8, Comunidad de Palo Blanco, Salamanca 36885, Mexico.
  • Centro de Investigación Científica y de Educación Superior de Ensenada (CICESE), División de Física Aplicada-Departamento de Óptica, Carretera Ensenada-Tijuana, No. 3918, Zona Playitas, Ensenada 22860, Mexico.

ORCID-Profile: Isaí Espinoza-Torres, Israel Martínez-Ramírez, Daniel Jauregui-Vazquez, Miguel Ernesto Gutiérrez-Rivera, Felipe de Jesús Torres-Del Carmen, Tania Lozano-Hernández

Förderung

  • Universidad de Guanajuato
  • CONAHCYT and PRODEP

Zitieren

APA

Espinoza-Torres, I., Martínez-Ramírez, I., Sierra-Hernández, J. M., Jauregui-Vazquez, D., Gutiérrez-Rivera, M. E., Carmen, F. J. T., & Lozano-Hernández, T. (2023). Measurement of Cutting Temperature in Interrupted Machining Using Optical Spectrometry. Sensors, 23(21), 8968. https://doi.org/10.3390/s23218968

Vancouver

Espinoza-Torres I, Martínez-Ramírez I, Sierra-Hernández JM, Jauregui-Vazquez D, Gutiérrez-Rivera ME, Carmen FJT, et al. Measurement of Cutting Temperature in Interrupted Machining Using Optical Spectrometry. Sensors. 2023;23(21):8968. doi:10.3390/s23218968

BibTeX
@article{EspinozaTorres2023,
  author = {Espinoza-Torres, Isaí and Martínez-Ramírez, Israel and Sierra-Hernández, Juan Manuel and Jauregui-Vazquez, Daniel and Gutiérrez-Rivera, Miguel Ernesto and Carmen, Felipe de Jesús Torres-Del and Lozano-Hernández, Tania},
  title = {Measurement of Cutting Temperature in Interrupted Machining Using Optical Spectrometry},
  journal = {Sensors},
  year = {2023},
  volume = {23},
  number = {21},
  pages = {8968},
  doi = {10.3390/s23218968}
}
Kostenlos starten →