EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Automated Interlayer Wall Height Compensation for Wire Based Directed Energy Deposition Additive Manufacturing

Jian Qin iD, Javier Vives, Parthiban Raja, Shakirudeen Lasisi iD, Chong Wang, Thomas Charrett iD, Jialuo Ding, Stewart Williams, Jonathan Mark Hallam iD, Ralph Tatam

Sensors · 16.10.2023 · 23 (20) · 8498

DOI: 10.3390/s23208498 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 16.10.2023. Verfasst von Jian Qin und 9 weiteren Autor:innen. Beteiligte Einrichtung: Welding and Additive Manufacturing Centre, Cranfield University, Cranfield MK43 0AL, UK. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Innovate UK, EPSRC, Engineering and Physical Sciences Research Council (EPSRC).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Part quality monitoring and control in wire-based directed energy deposition additive manufacturing (w-DEDAM) processes has been garnering continuous interest from both the academic and industrial sectors. However, maintaining a consistent layer height and ensuring that the wall height aligns closely with the design, as depicted in computer-aided design (CAD) models, pose significant challenges. These challenges arise due to the uncertainties associated with the manufacturing process and the working environment, particularly with extended processing times. To achieve these goals in an industrial scenario, the deposition geometry must be measured with precision and efficiency throughout the part-building process. Moreover, it is essential to comprehend the changes in the interlayer deposition height based on various process parameters. This paper first examines the behaviour of interlayer deposition height when process parameters change within different wall regions, with a particular focus on the transition areas. In addition, this paper explores the potential of geometry monitoring information in implementing interlayer wall height compensation during w-DEDAM part-building. The in-process layer height was monitored using a coherent range-resolved interferometry (RRI) sensor, and the accuracy and efficiency of this measurement were carefully studied. Leveraging this information and understanding of deposition geometry, the control points of the process parameters were identified. Subsequently, appropriate and varied process parameters were applied to each wall region to gradually compensate for wall height. The wall height discrepancies were generally compensated for in two to three layers.

Schlagwörter

Stichwörter der Autor:innen

interlayer wall height compensationpart quality monitoring and controlwire-based directed energy deposition additive manufacturing (w-DEDAM)

Autor:innen und Institutionen

  • Welding and Additive Manufacturing Centre, Cranfield University, Cranfield MK43 0AL, UK.
  • WAAM3D Limited, Thornton Chase, Linford Wood, Milton Keynes MK14 6FD, UK.
  • Centre for Engineering Photonics, Cranfield University, Cranfield MK43 0AL, UK.

ORCID-Profile: Jian Qin, Shakirudeen Lasisi, Thomas Charrett, Jonathan Mark Hallam

Förderung

  • Innovate UK
  • EPSRC
  • Engineering and Physical Sciences Research Council (EPSRC)

Zitieren

APA

Qin, J., Vives, J., Raja, P., Lasisi, S., Wang, C., Charrett, T., Ding, J., Williams, S., Hallam, J. M., & Tatam, R. (2023). Automated Interlayer Wall Height Compensation for Wire Based Directed Energy Deposition Additive Manufacturing. Sensors, 23(20), 8498. https://doi.org/10.3390/s23208498

Vancouver

Qin J, Vives J, Raja P, Lasisi S, Wang C, Charrett T, et al. Automated Interlayer Wall Height Compensation for Wire Based Directed Energy Deposition Additive Manufacturing. Sensors. 2023;23(20):8498. doi:10.3390/s23208498

BibTeX
@article{Qin2023,
  author = {Qin, Jian and Vives, Javier and Raja, Parthiban and Lasisi, Shakirudeen and Wang, Chong and Charrett, Thomas and Ding, Jialuo and Williams, Stewart and Hallam, Jonathan Mark and Tatam, Ralph},
  title = {Automated Interlayer Wall Height Compensation for Wire Based Directed Energy Deposition Additive Manufacturing},
  journal = {Sensors},
  year = {2023},
  volume = {23},
  number = {20},
  pages = {8498},
  doi = {10.3390/s23208498}
}
Kostenlos starten →