Biomechanical Load of Neck and Lumbar Joints in Open-Surgery Training
Sensors · 2023
DOI: 10.3390/s23156974 ↗Kurz gefasst
Fachartikel in der Zeitschrift Sensors, 2023. Verfasst von Ce Zhang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Rehabilitation Medicine, University of Groningen, University Medical Center Groningen, Hanzeplein 1, 9713 GZ Groningen, The Netherlands. Hauptthemen laut MEDLINE: Lumbar Vertebrae, Joints. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: China Scholarship Council.
Abstract (Originalsprache)
The prevalence of musculoskeletal symptoms (MSS) like neck and back pain is high among open-surgery surgeons. Prolonged working in the same posture and unfavourable postures are biomechanical risk factors for developing MSS. Ergonomic devices such as exoskeletons are possible solutions that can reduce muscle and joint load. To design effective exoskeletons for surgeons, one needs to quantify which neck and trunk postures are seen and how much support during actual surgery is required. Hence, this study aimed to establish the biomechanical profile of neck and trunk postures and neck and lumbar joint loads during open surgery (training). Eight surgical trainees volunteered to participate in this research. Neck and trunk segment orientations were recorded using an inertial measurement unit (IMU) system during open surgery (training). Neck and lumbar joint kinematics, joint moments and compression forces were computed using OpenSim modelling software and a musculoskeletal model. Histograms were used to illustrate the joint angle and load distribution of the neck and lumbar joints over time. During open surgery, the neck flexion angle was 71.6% of the total duration in the range of 10~40 degrees, and lumbar flexion was 68.9% of the duration in the range of 10~30 degrees. The normalized neck and lumbar flexion moments were 53.8% and 35.5% of the time in the range of 0.04~0.06 Nm/kg and 0.4~0.6 Nm/kg, respectively. Furthermore, the neck and lumbar compression forces were 32.9% and 38.2% of the time in the range of 2.0~2.5 N/kg and 15~20 N/kg, respectively. In contrast to exoskeletons used for heavy lifting tasks, exoskeletons designed for surgeons exhibit lower support torque requirements while additional degrees of freedom (DOF) are needed to accommodate combinations of neck and trunk postures.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Rehabilitation Medicine, University of Groningen, University Medical Center Groningen, Hanzeplein 1, 9713 GZ Groningen, The Netherlands.
- Center for Human Movement Sciences, University of Groningen, University Medical Center Groningen, Hanzeplein 1, 9713 GZ Groningen, The Netherlands.
- Department of Biomechanical Engineering, University of Twente, Drienerlolaan 5, 7522 NB Enschede, The Netherlands.
ORCID-Profile: Ce Zhang, Charlotte Christina Roossien, Han Houdijk
Förderung
- China Scholarship Council
Zitieren
APA
Zhang, C., Roossien, C. C., Verkerke, G. J., Houdijk, H., Hijmans, J. M., & Greve, C. (2023). Biomechanical Load of Neck and Lumbar Joints in Open-Surgery Training. Sensors. https://doi.org/10.3390/s23156974
Vancouver
Zhang C, Roossien CC, Verkerke GJ, Houdijk H, Hijmans JM, Greve C. Biomechanical Load of Neck and Lumbar Joints in Open-Surgery Training. Sensors. 2023. doi:10.3390/s23156974
BibTeX
@article{Zhang2023,
author = {Zhang, Ce and Roossien, Charlotte Christina and Verkerke, Gijsbertus Jacob and Houdijk, Han and Hijmans, Juha M and Greve, Christian},
title = {Biomechanical Load of Neck and Lumbar Joints in Open-Surgery Training},
journal = {Sensors},
year = {2023},
doi = {10.3390/s23156974}
}
EUVIMED