EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Wideband SiGe-HBT Low-Noise Amplifier with Resistive Feedback and Shunt Peaking

Ickhyun Song iD, Gyungtae Ryu, Seung Hwan Jung iD, John D Cressler, Moon-Kyu Cho

Sensors · 28.07.2023 · 23 (15) · 6745

DOI: 10.3390/s23156745 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 28.07.2023. Verfasst von Ickhyun Song und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Electronic Engineering, Hanyang University, Seoul 04763, Republic of Korea. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Korea government (MSIT), Ministry of Education (MOE), Hanyang University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, the design of a wideband low-noise amplifier (LNA) using a resistive feedback network is proposed for potential multi-band sensing, communication, and radar applications. For achieving wide operational bandwidth and flat in-band characteristics simultaneously, the proposed LNA employs a variety of circuit design techniques, including a voltage–current (shunt–shunt) negative feedback configuration, inductive emitter degeneration, a main branch with an added cascode stage, and the shunt-peaking technique. The use of a feedback network and emitter degeneration provides broadened transfer characteristics for multi-octave coverage and a real impedance for input matching, respectively. In addition, the cascode stage pushes the band-limiting low-frequency pole, due to the Miller capacitance, to a higher frequency. Lastly, the shunt-peaking approach is optimized for the compensation of a gain reduction at higher frequency bands. The wideband LNA proposed in this study is fabricated using a commercial 0.13 μm silicon-germanium (SiGe) BiCMOS process, employing SiGe heterojunction bipolar transistors (HBTs) as the circuit’s core active elements in the main branch. The measurement results show an operational bandwidth of 2.0–29.2 GHz, a noise figure of 4.16 dB (below 26.5 GHz, which was the measurement limit), and a total power consumption of 23.1 mW under a supply voltage of 3.3 V. Regarding the nonlinearity associated with large-signal behavior, the proposed LNA exhibits an input 1-dB compression (IP1dB) point of −5.42 dBm at 12 GHz. These performance numbers confirm the strong viability of the proposed approach in comparison with other state-of-the-art designs.

Schlagwörter

Stichwörter der Autor:innen

SiGe HBTcascodeinductive emitter degenerationlow-noise amplifier (LNA)resistive feedbackshunt peakingwideband

Autor:innen und Institutionen

  • Department of Electronic Engineering, Hanyang University, Seoul 04763, Republic of Korea.
  • Division of Nanoscale Semiconductor Engineering, Hanyang University, Seoul 04763, Republic of Korea.
  • GRIT Custom-IC Corp., Seoul 01886, Republic of Korea.
  • School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30318, USA.
  • Department of Computer Engineering, Korea National University of Transportation, Chungju-si 27469, Republic of Korea.

ORCID-Profile: Ickhyun Song, Seung Hwan Jung

Förderung

  • Korea government (MSIT)
  • Ministry of Education (MOE)
  • Hanyang University
  • Korea National University of Transportation Industry-Academy Cooperation Foundation

Zitieren

APA

Song, I., Ryu, G., Jung, S. H., Cressler, J. D., & Cho, M. K. (2023). Wideband SiGe-HBT Low-Noise Amplifier with Resistive Feedback and Shunt Peaking. Sensors, 23(15), 6745. https://doi.org/10.3390/s23156745

Vancouver

Song I, Ryu G, Jung SH, Cressler JD, Cho MK. Wideband SiGe-HBT Low-Noise Amplifier with Resistive Feedback and Shunt Peaking. Sensors. 2023;23(15):6745. doi:10.3390/s23156745

BibTeX
@article{Song2023,
  author = {Song, Ickhyun and Ryu, Gyungtae and Jung, Seung Hwan and Cressler, John D and Cho, Moon-Kyu},
  title = {Wideband SiGe-HBT Low-Noise Amplifier with Resistive Feedback and Shunt Peaking},
  journal = {Sensors},
  year = {2023},
  volume = {23},
  number = {15},
  pages = {6745},
  doi = {10.3390/s23156745}
}
Kostenlos starten →