EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Workflow for Studying the Stump–Socket Interface in Persons with Transtibial Amputation through 3D Thermographic Mapping

Andrea Giovanni Cutti iD, Federico Morosato iD, Cosimo Gentile iD, Francesca Gariboldi, Giovanni Hamoui iD, Maria Grazia Santi, Gregorio Teti, Emanuele Gruppioni iD

Sensors · 2023

DOI: 10.3390/s23115035 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, 2023. Verfasst von Andrea Giovanni Cutti und 7 weiteren Autor:innen. Beteiligte Einrichtung: Centro Protesi Inail, Via Rabuina 14, Vigorso di Budrio, 40054 Bologna, Italy. Hauptthemen laut MEDLINE: Quality of Life, Artificial Limbs. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The design and fitting of prosthetic sockets can significantly affect the acceptance of an artificial limb by persons with lower limb amputations. Clinical fitting is typically an iterative process, which requires patients’ feedback and professional assessment. When feedback is unreliable due to the patient’s physical or psychological conditions, quantitative measures can support decision-making. Specifically, monitoring the skin temperature of the residual limb can provide valuable information regarding unwanted mechanical stresses and reduced vascularization, which can lead to inflammation, skin sores and ulcerations. Multiple 2D images to examine a real-life 3D limb can be cumbersome and might only offer a partial assessment of critical areas. To overcome these issues, we developed a workflow for integrating thermographic information on the 3D scan of a residual limb, with intrinsic reconstruction quality measures. Specifically, workflow allows us to calculate a 3D thermal map of the skin of the stump at rest and after walking, and summarize this information with a single 3D differential map. The workflow was tested on a person with transtibial amputation, with a reconstruction accuracy lower than 3 mm, which is adequate for socket adaptation. We expect the workflow to improve socket acceptance and patients’ quality of life.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Quality of LifeArtificial LimbsHumansWorkflowProsthesis DesignAmputation, SurgicalAmputation StumpsTibia

Stichwörter der Autor:innen

3D thermographylower limb amputationthermal imaging

Autor:innen und Institutionen

  • Centro Protesi Inail, Via Rabuina 14, Vigorso di Budrio, 40054 Bologna, Italy.
  • Department of Industrial Engineering, University of Padova, Via VIII Febbraio, 2, 35122 Padova, Italy.

ORCID-Profile: Andrea Giovanni Cutti, Federico Morosato, Cosimo Gentile, Giovanni Hamoui, Emanuele Gruppioni

Zitieren

APA

Cutti, A. G., Morosato, F., Gentile, C., Gariboldi, F., Hamoui, G., Santi, M. G., Teti, G., & Gruppioni, E. (2023). A Workflow for Studying the Stump–Socket Interface in Persons with Transtibial Amputation through 3D Thermographic Mapping. Sensors. https://doi.org/10.3390/s23115035

Vancouver

Cutti AG, Morosato F, Gentile C, Gariboldi F, Hamoui G, Santi MG, et al. A Workflow for Studying the Stump–Socket Interface in Persons with Transtibial Amputation through 3D Thermographic Mapping. Sensors. 2023. doi:10.3390/s23115035

BibTeX
@article{Cutti2023,
  author = {Cutti, Andrea Giovanni and Morosato, Federico and Gentile, Cosimo and Gariboldi, Francesca and Hamoui, Giovanni and Santi, Maria Grazia and Teti, Gregorio and Gruppioni, Emanuele},
  title = {A Workflow for Studying the Stump–Socket Interface in Persons with Transtibial Amputation through 3D Thermographic Mapping},
  journal = {Sensors},
  year = {2023},
  doi = {10.3390/s23115035}
}
Kostenlos starten →