EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Model Updating Concept Using Bridge Weigh-in-Motion Data

Doron Hekič iD, Andrej Anžlin iD, Maja Kreslin, Aleš Žnidarič iD, Peter Češarek

Sensors · 12.02.2023 · 23 (4) · 2067

DOI: 10.3390/s23042067 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 12.02.2023. Verfasst von Doron Hekič und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Civil and Geodetic Engineering, University of Ljubljana, Jamova cesta 2, 1000 Ljubljana, Slovenia. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovenian Research Agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Finite element (FE) model updating of bridges is based on the measured modal parameters and less frequently on the measured structural response under a known load. Until recently, the FE model updating did not consider strain measurements from sensors installed for weighing vehicles with bridge weigh-in-motion (B-WIM) systems. A 50-year-old multi-span concrete highway viaduct, renovated between 2017 and 2019, was equipped with continuous monitoring system with over 200 sensors, and a B-WIM system. In the most heavily instrumented span, the maximum measured longitudinal strains induced by the full-speed calibration vehicle passages were compared with the modelled strains. Based on the sensitivity study results, three variables that affected its overall stiffness were updated: Young’s modulus adjustment factor of all structural elements, and two anchorage reduction factors that considered the interaction between the superstructure and non-structural elements. The analysis confirmed the importance of the initial manual FE model updating to correctly reflect the non-structural elements during the automatic nonlinear optimisation. It also demonstrated a successful use of pseudo-static B-WIM loading data during the model updating process and the potential to extend the proposed approach to using random B-WIM-weighed vehicles for FE model updating and long-term monitoring of structural parameters and load-dependent phenomena.

Schlagwörter

Stichwörter der Autor:innen

bridgebridge weigh-in-motion (B-WIM)calibrationfinite element (FE)model updatingmonitoringstructural health monitoring (SHM)viaduct

Autor:innen und Institutionen

  • Faculty of Civil and Geodetic Engineering, University of Ljubljana, Jamova cesta 2, 1000 Ljubljana, Slovenia.
  • Department of Structures, Slovenian National Building and Civil Engineering Institute, Dimičeva ulica 12, 1000 Ljubljana, Slovenia.

ORCID-Profile: Doron Hekič, Andrej Anžlin, Aleš Žnidarič

Förderung

  • Slovenian Research Agency

Zitieren

APA

Hekič, D., Anžlin, A., Kreslin, M., Žnidarič, A., & Češarek, P. (2023). Model Updating Concept Using Bridge Weigh-in-Motion Data. Sensors, 23(4), 2067. https://doi.org/10.3390/s23042067

Vancouver

Hekič D, Anžlin A, Kreslin M, Žnidarič A, Češarek P. Model Updating Concept Using Bridge Weigh-in-Motion Data. Sensors. 2023;23(4):2067. doi:10.3390/s23042067

BibTeX
@article{Heki2023,
  author = {Hekič, Doron and Anžlin, Andrej and Kreslin, Maja and Žnidarič, Aleš and Češarek, Peter},
  title = {Model Updating Concept Using Bridge Weigh-in-Motion Data},
  journal = {Sensors},
  year = {2023},
  volume = {23},
  number = {4},
  pages = {2067},
  doi = {10.3390/s23042067}
}
Kostenlos starten →