EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Integrated Design of a Modular Lower-Limb Rehabilitation Exoskeleton: Multibody Simulation, Load-Driven Structural Optimization, and Experimental Validation

Ionut Geonea, Andrei Corzanu, Cristian Copilusi, Adriana Ionescu, Daniela Tarnita

Robotics · 28.03.2026 · 15 (4) · 71

DOI: 10.3390/robotics15040071 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Robotics, online erschienen am 28.03.2026. Verfasst von Ionut Geonea und 4 weiteren Autor:innen. Die Arbeit nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lower-limb rehabilitation exoskeletons must balance biomechanical compatibility, structural safety, and low mass to enable practical, repeatable gait assistance. This paper proposes a planar pantograph-derived exoskeleton leg driven by a Chebyshev Lambda linkage and develops an integrated workflow from mechanism synthesis to manufacturable optimization and experimental verification. A mannequin-coupled multibody model was built in MSC ADAMS to evaluate joint kinematics, end-point (foot) trajectories, and joint reaction forces under multiple scenarios (fixed-frame, ramp, stair ascent, and inclined-plane walking). The extracted joint loads were transferred to a parametric finite element model in ANSYS Workbench 2019, where response surface surrogates and a multi-objective genetic algorithm (MOGA) were used to minimize mass under stiffness and strength constraints. For the optimized load-bearing link, the selected minimum-mass design reached a component mass of 0.542 kg while respecting the imposed structural limits, i.e., a maximum total deformation below 0.2 mm and a maximum equivalent (von Mises) stress below 50 MPa (e.g., ~0.188 mm deformation and ~39 MPa stress in the optimal candidate). A rapid prototype was manufactured by 3D printing and experimentally evaluated using CONTEMPLAS high-speed video tracking, providing measured XM(t) and YM(t) trajectories and joint-angle histories for quantitative comparison with simulations via RMSE metrics.

Zitieren

APA

Geonea, I., Corzanu, A., Copilusi, C., Ionescu, A., & Tarnita, D. (2026). Integrated Design of a Modular Lower-Limb Rehabilitation Exoskeleton: Multibody Simulation, Load-Driven Structural Optimization, and Experimental Validation. Robotics, 15(4), 71. https://doi.org/10.3390/robotics15040071

Vancouver

Geonea I, Corzanu A, Copilusi C, Ionescu A, Tarnita D. Integrated Design of a Modular Lower-Limb Rehabilitation Exoskeleton: Multibody Simulation, Load-Driven Structural Optimization, and Experimental Validation. Robotics. 2026;15(4):71. doi:10.3390/robotics15040071

BibTeX
@article{Geonea2026,
  author = {Geonea, Ionut and Corzanu, Andrei and Copilusi, Cristian and Ionescu, Adriana and Tarnita, Daniela},
  title = {Integrated Design of a Modular Lower-Limb Rehabilitation Exoskeleton: Multibody Simulation, Load-Driven Structural Optimization, and Experimental Validation},
  journal = {Robotics},
  year = {2026},
  volume = {15},
  number = {4},
  pages = {71},
  doi = {10.3390/robotics15040071}
}
Kostenlos starten →