Valorization of Minimally Processed Blast Furnace Slag in Industrial Mortars: Early-Age Performance and Embodied Carbon Reduction
Recycling · 14.07.2026 · 11 (7) · 122
DOI: 10.3390/recycling11070122 ↗Kurz gefasst
Fachartikel in der Zeitschrift Recycling, online erschienen am 14.07.2026. Verfasst von Houssam Affan und 5 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Conventional valorization of blast furnace slag commonly involves granulation, fine grinding, mechanical activation, or chemical activation, which increase energy demand and processing complexity. This study investigated a minimally processed blast furnace slag (MP-BFS), defined here as the fraction passing 64 µm obtained by sieving a 0–8 mm industrial material without grinding, additional granulation, thermal treatment, or chemical activation. MP-BFS replaced 10–50% of the cement by mass to reduce clinker in industrial mortars formulated at a constant flow spread of 23–24 cm and tested from 8 h to 90 d. Bulk density, water-accessible porosity, total and capillary water absorption, and compressive and flexural strengths were evaluated. Replacing 10% of the cement with slag improved compressive strength from the earliest test age and increased the 28-day compressive and flexural strengths by 5.1% and 9.5%, respectively, relative to the control mortar; this response coincided with a reduction in measured porosity from 8.95% to 8.01%. This improvement is consistent with a physical filling effect and improved particle packing, although these mechanisms were not directly verified by microstructural analyses. At higher replacement levels, water-accessible porosity increased, reaching 24.45% at 50% slag replacement, alongside greater water ingress and delayed strength development. Exploratory empirical regression analyses described associations among slag content, porosity, water transfer, and compressive strength within the investigated formulations. A simplified screening-level constituent-production-and-transport comparison per cubic meter, based on generic ICE factors and an assumed 50 km transport distance, estimated a maximum embodied carbon reduction of 44% at 50% replacement. Curing energy, use, carbonation, maintenance, and end-of-life stages were excluded. Overall, 10% MP-BFS replacement provided the most favorable performance–carbon content balance, whereas 30–50% achieved larger carbon reductions but showed early-age strength losses that limit their suitability for rapid-demolding applications under the investigated conditions.
Zitieren
APA
Affan, H., Fehr, L., Al-Massri, G., Alassaad, F., Yaghi, A., & Ghanem, H. (2026). Valorization of Minimally Processed Blast Furnace Slag in Industrial Mortars: Early-Age Performance and Embodied Carbon Reduction. Recycling, 11(7), 122. https://doi.org/10.3390/recycling11070122
Vancouver
Affan H, Fehr L, Al-Massri G, Alassaad F, Yaghi A, Ghanem H. Valorization of Minimally Processed Blast Furnace Slag in Industrial Mortars: Early-Age Performance and Embodied Carbon Reduction. Recycling. 2026;11(7):122. doi:10.3390/recycling11070122
BibTeX
@article{Affan2026,
author = {Affan, Houssam and Fehr, Laurent and Al-Massri, Ginan and Alassaad, Farjallah and Yaghi, Amro and Ghanem, Hassan},
title = {Valorization of Minimally Processed Blast Furnace Slag in Industrial Mortars: Early-Age Performance and Embodied Carbon Reduction},
journal = {Recycling},
year = {2026},
volume = {11},
number = {7},
pages = {122},
doi = {10.3390/recycling11070122}
}
EUVIMED