EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Recycling of Scrap Metal from Multifunctional Aluminum-Based Electronic Device Housings

Wojciech Szymański, Sonia Boczkal, Dawid Kapinos, Joanna Hrabia-Wiśnios, Elżbieta Szymańska, Lutz Stobbe, Thomas Mager, Marek Kościelski

Recycling · 08.05.2026 · 11 (5) · 88

DOI: 10.3390/recycling11050088 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Recycling, online erschienen am 08.05.2026. Verfasst von Wojciech Szymański und 7 weiteren Autor:innen. Die Arbeit nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Center for Research and Development (Poland) and the Federal Ministry for Economic Affairs and Climate Action.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aluminum multifunctional housings can enhance circularity in electronics by replacing polymer enclosures while integrating heat sinking and electronic functions via laser direct structuring (LDS). Within the ALU4CED concept, we applied an IR-compatible LDS lacquer on aluminum, formed conductive tracks by electroless Cu/Ni/Au metallization, assembled components, and assessed end-of-life recyclability. Controlled remelting trials compared three disassembly levels: complete housings with PCBs and components, housings without PCBs, and housings with only integrated tracks. Metal yield rose from 81.4% for complete assemblies to 93.2% after PCB removal, while leaving integrated LDS tracks did not measurably penalize recovery. Only the complete electronics variant showed critical contamination (Cu = 1.64 wt.% vs. 0.25 wt.% limit for EN AC 4343); after PCB removal, composition remained close to the reference and major elements (Si, Mg, Fe) stayed within specification. Prefil testing indicated very low total inclusion content (0.006/0.001/0.002 mm2·kg−1), confirming high melt cleanliness despite coatings. Following remelting → billet casting → extrusion, tensile properties (Rm ≈ 120–123 MPa, Rp0.2 ≈ 59–61 MPa, A ≈ 29–33%) were comparable to the reference profile. These results demonstrate the technological feasibility of closed-loop recycling for LDS functionalized aluminum housings and inform clear Design-for-Recycling guidance: design for rapid PCB removal, allow LDS layers to remain during melting, and maintain compatibility with the 4343 family to enable efficient internal recycling.

Förderung

  • National Center for Research and Development (Poland) and the Federal Ministry for Economic Affairs and Climate Action

Zitieren

APA

Szymański, W., Boczkal, S., Kapinos, D., Hrabia-Wiśnios, J., Szymańska, E., Stobbe, L., Mager, T., & Kościelski, M. (2026). Recycling of Scrap Metal from Multifunctional Aluminum-Based Electronic Device Housings. Recycling, 11(5), 88. https://doi.org/10.3390/recycling11050088

Vancouver

Szymański W, Boczkal S, Kapinos D, Hrabia-Wiśnios J, Szymańska E, Stobbe L, et al. Recycling of Scrap Metal from Multifunctional Aluminum-Based Electronic Device Housings. Recycling. 2026;11(5):88. doi:10.3390/recycling11050088

BibTeX
@article{Szymaski2026,
  author = {Szymański, Wojciech and Boczkal, Sonia and Kapinos, Dawid and Hrabia-Wiśnios, Joanna and Szymańska, Elżbieta and Stobbe, Lutz and Mager, Thomas and Kościelski, Marek},
  title = {Recycling of Scrap Metal from Multifunctional Aluminum-Based Electronic Device Housings},
  journal = {Recycling},
  year = {2026},
  volume = {11},
  number = {5},
  pages = {88},
  doi = {10.3390/recycling11050088}
}
Kostenlos starten →