EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Cuttings Migration Below the Gas-Injection Point in Air-Lift Reverse-Circulation Drilling: A Reduced-Order Model

Pu Liu, Jieyu Xiao, Chuanhua Ge, Yingjie Li, Ruiqi Zhang

Processes · 06.11.2026 · 14 (21) · 3602

DOI: 10.3390/pr14213602 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 06.11.2026. Verfasst von Pu Liu und 4 weiteren Autor:innen. Die Arbeit nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Sichuan Provincial Department of Education.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Severe lost circulation in fractured shale formations limits the safe and efficient implementation of drilling operations, and the cuttings-migration behavior below the gas-injection point, which governs the cuttings-return performance of air-lift reverse circulation (ALRC) drilling, remains poorly quantified. To address this gap, this study develops a reduced-order liquid–solid model for cuttings migration below the gas-injection point, while the upper gas-lift zone is represented only through hydraulic pressure coupling. Agglomerated cuttings are treated as a continuous phase, the drill-pipe cross-section is discretized into radial layers to capture the radial velocity distribution of the liquid phase, and a quasi-steady spatial-marching algorithm with a local-equilibrium slip closure is adopted to simulate long-distance cuttings transport. Under the no-interlayer-exchange assumption, the model predicts strong near-wall cuttings retention during gas-free liquid–solid circulation. This result is interpreted as a conservative, model-dependent transport estimate rather than a direct prediction of permanent field-scale retention. In the Nr = 10 calculation, gas injection at 800 m above the bottom hole increases the predicted near-wall cuttings-migration height by approximately 13.8% relative to the gas-free case. For the composite reference case, gas-injection heights of 600, 700, and 800 m above the bottom hole are compared at a fixed gas flow rate of 0.100 m3 s−1. Among the three discrete heights tested at the finest investigated radial resolution, 600 m produced the largest fraction of inlet cuttings mass reaching the gas-injection interface. This result establishes only the relative ranking of the three tested cases and does not identify a continuously optimized or meter-scale gas-injection position. The 13.27 m difference between the Nr = 8 and Nr = 10 predictions is retained as an indicator of unresolved radial-resolution sensitivity.

Förderung

  • Sichuan Provincial Department of Education

Zitieren

APA

Liu, P., Xiao, J., Ge, C., Li, Y., & Zhang, R. (2026). Cuttings Migration Below the Gas-Injection Point in Air-Lift Reverse-Circulation Drilling: A Reduced-Order Model. Processes, 14(21), 3602. https://doi.org/10.3390/pr14213602

Vancouver

Liu P, Xiao J, Ge C, Li Y, Zhang R. Cuttings Migration Below the Gas-Injection Point in Air-Lift Reverse-Circulation Drilling: A Reduced-Order Model. Processes. 2026;14(21):3602. doi:10.3390/pr14213602

BibTeX
@article{Liu2026,
  author = {Liu, Pu and Xiao, Jieyu and Ge, Chuanhua and Li, Yingjie and Zhang, Ruiqi},
  title = {Cuttings Migration Below the Gas-Injection Point in Air-Lift Reverse-Circulation Drilling: A Reduced-Order Model},
  journal = {Processes},
  year = {2026},
  volume = {14},
  number = {21},
  pages = {3602},
  doi = {10.3390/pr14213602}
}
Kostenlos starten →