EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Preparation and Plugging Performance Evaluation of Epoxy Resin Particles via an Optimized Synthesis Method

Jun Zhang, Sheng Fan, Zhong He, Xin Zheng, Shifeng Zhang

Processes · 13.04.2026 · 14 (8) · 1242

DOI: 10.3390/pr14081242 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 13.04.2026. Verfasst von Jun Zhang und 4 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: key technology of efficient drilling in fault-controlled reservoir in the Shunbei gas area.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To overcome polymer-based plugging materials’ disadvantage of being prone to degradation and failure under hydrothermal conditions, an epoxy resin plugging particle with a high-pressure-bearing capacity under high temperatures was prepared by optimizing the curing process. Bisphenol A Epoxy Resin E51 and Diethyltoluenediamine (DETDA) were selected as raw materials for sample preparation. Due to the high viscosity of the system, 1,2-cyclohexanediol diglycidyl ether was introduced as a diluent, and an optimal concentration of 20% was determined through experimental optimization. Non-isothermal differential scanning calorimetry, bottle testing, and infrared spectroscopy were employed to investigate the variation laws of curing temperature, curing time and curing degree during the epoxy resin curing process via one-step and multi-step methods. The compressive strength of the epoxy resin prepared using the two processes was evaluated. After comprehensively comparing the preparation time, process complexity, and compressive strength of the final samples of the one-step and two-step curing methods, the one-step process (90 °C/5 h) was determined to be superior. In addition, the results of the fracture plugging experiment showed that after the bulk epoxy resin prepared using the optimized process was made into particles through a mechanical method and treated under hydrothermal conditions at 120 °C, the maximum breakthrough pressure reached 4.2 MPa, which was 950% and 135.96% higher than that of Particle 1 (Poly(2-acrylamido-2-methylpropanesulfonic acid)/acrylamide (PAMPS/AM) gel) and Particle 2 (PAMPS/AM gel treated with Polyethylene glycol (PEG)), respectively, which were used as control groups. This result indicates that epoxy resin can be used as a high-temperature-resistant plugging material and should be further researched.

Förderung

  • key technology of efficient drilling in fault-controlled reservoir in the Shunbei gas area

Zitieren

APA

Zhang, J., Fan, S., He, Z., Zheng, X., & Zhang, S. (2026). Preparation and Plugging Performance Evaluation of Epoxy Resin Particles via an Optimized Synthesis Method. Processes, 14(8), 1242. https://doi.org/10.3390/pr14081242

Vancouver

Zhang J, Fan S, He Z, Zheng X, Zhang S. Preparation and Plugging Performance Evaluation of Epoxy Resin Particles via an Optimized Synthesis Method. Processes. 2026;14(8):1242. doi:10.3390/pr14081242

BibTeX
@article{Zhang2026,
  author = {Zhang, Jun and Fan, Sheng and He, Zhong and Zheng, Xin and Zhang, Shifeng},
  title = {Preparation and Plugging Performance Evaluation of Epoxy Resin Particles via an Optimized Synthesis Method},
  journal = {Processes},
  year = {2026},
  volume = {14},
  number = {8},
  pages = {1242},
  doi = {10.3390/pr14081242}
}
Kostenlos starten →