EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimized Machining Parameters for High-Speed Turning Process: A Comparative Study of Dry and Cryo+MQL Techniques

Nabil Jouini, Jaharah A. Ghani, Saima Yaqoob, Afifah Zakiyyah Juri

Processes · 04.03.2025 · 13 (3) · 739

DOI: 10.3390/pr13030739 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 04.03.2025. Verfasst von Nabil Jouini und 3 weiteren Autor:innen. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Prince Sattam bin Abdulaziz University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Hard turning is a precision machining process used to cut materials with hardnesses exceeding 45 HRC using single-point tools. It offers an efficient alternative to traditional grinding for finishing operations in manufacturing. This paper explores the machinability of hardened AISI 4340 steel for a hard turning process utilizing dry and cryogenic (Cryo) plus minimum quantity lubrication (MQL) (Cryo+MQL) techniques, focusing on critical machinability aspects such as cutting force, surface roughness, and tool life. The orthogonal dry turning was performed with a cutting speed (V) ranging from 300–400 m/min, a feed rate (f) between 0.05 and 1 mm/rev, and a depth of cut (doc) from 0.1 to 0.3 mm. A statistical analysis of the obtained results revealed that the feed rate was the most influential parameter, contributing 50.69% to the main cutting force and 80.03% to surface roughness. For tool life, cutting speed was identified as the dominant factor, with a contribution rate of 39.73%. Multi-objective optimization using Grey relational analysis (GRA) identified the optimal machining parameters for the hard turning of AISI 4340 alloy steel as V = 300 m/min, f = 0.05 mm/rev, and doc = 0.1 mm. The Cryo+MQL technique was subsequently applied to these parameters, yielding significant improvements, with a 48% reduction in surface roughness and a 184.5% increase in tool life, attributed to enhanced lubrication and cooling efficiency. However, a slight 4.6% increase in cutting force was observed, likely due to surface hardening induced by the low-temperature LN2 cooling. Furthermore, reduced adhesion and tool fracture on the principal cutting edge under Cryo+MQL conditions justify the superior surface quality and extended tool life achieved. This research highlights the industrial relevance of hybrid lubrication in addressing challenges associated with hard turning processes.

Förderung

  • Prince Sattam bin Abdulaziz University

Zitieren

APA

Jouini, N., Ghani, J. A., Yaqoob, S., & Juri, A. Z. (2025). Optimized Machining Parameters for High-Speed Turning Process: A Comparative Study of Dry and Cryo+MQL Techniques. Processes, 13(3), 739. https://doi.org/10.3390/pr13030739

Vancouver

Jouini N, Ghani JA, Yaqoob S, Juri AZ. Optimized Machining Parameters for High-Speed Turning Process: A Comparative Study of Dry and Cryo+MQL Techniques. Processes. 2025;13(3):739. doi:10.3390/pr13030739

BibTeX
@article{Jouini2025,
  author = {Jouini, Nabil and Ghani, Jaharah A. and Yaqoob, Saima and Juri, Afifah Zakiyyah},
  title = {Optimized Machining Parameters for High-Speed Turning Process: A Comparative Study of Dry and Cryo+MQL Techniques},
  journal = {Processes},
  year = {2025},
  volume = {13},
  number = {3},
  pages = {739},
  doi = {10.3390/pr13030739}
}
Kostenlos starten →