EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Surface Treatment on Adhesive Performance of Composite-to-Composite and Composite-to-Metal Joints

Nikhil Paranjpe, Md. Nizam Uddin, Akm Samsur Rahman, Ramazan Asmatulu

Processes · 21.11.2024 · 12 (12) · 2623

DOI: 10.3390/pr12122623 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 21.11.2024. Verfasst von Nikhil Paranjpe und 3 weiteren Autor:innen. Die Arbeit wurde bisher 38-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study deals with the long-running challenge of joining similar and dissimilar materials using composite-to-composite and composite-to-metal joints. This research was conducted to evaluate the effects of surface morphology and surface treatments on the mechanical performance of adhesively bonded joints used for the aircraft industry. A two-segment, commercially available, toughened epoxy was chosen as the adhesive. Unidirectional carbon fiber prepreg and aluminum 2021-T3 alloys were chosen for the composite and metal panels, respectively. Surface treatment of the metal included corrosion elimination followed by a passive surface coating of Alodine®. A combination of surface treatment methods was used for the composite and metal specimens, including detergent cleaning, plasma exposure, and sandblasting. The shear strength of the single-lap adhesive joint was evaluated according to the ASTM D1002. Ultraviolet (UV) and plasma exposure effects were studied by measuring the water contact angles. The test results showed that the aluminum adherent treated with sandblasting, detergent, and UV irradiation resulted in the strongest adhesive bonding of the composite-to-composite panels, while the composite-to-metal sample cleaned only with detergent resulted in the least bonding strength. The failure strain of the composite-to-composite bonding was reduced by approximately 50% with only sandblasting. However, extended treatment did not introduce additional brittleness in the adhesive joint. The bonding strength of the composite-to-composite panel improved by approximately 35% with plasma treatment alone because of the better surface functionalization and bonding strength. In the composite-to-aluminum bonding process, exposing the aluminum surface to UV resulted in 30% more joint strength compared to the Alodine® coating, which suggests the origination of higher orders of magnitude of covalent groups from the surface. A comparison with published results found that the joint strengths in both similar and dissimilar specimens are higher than most other results. Detailed observations and surface analysis studies showed that the composite-to-composite bonding mainly failed due to adhesive and cohesive failures; however, failure of the composite-to-aluminum bonding was heterogeneous, where adhesive failure occurred on the aluminum side and substrate failure occurred on the composite side.

Zitieren

APA

Paranjpe, N., Uddin, M. N., Rahman, A. S., & Asmatulu, R. (2024). Effects of Surface Treatment on Adhesive Performance of Composite-to-Composite and Composite-to-Metal Joints. Processes, 12(12), 2623. https://doi.org/10.3390/pr12122623

Vancouver

Paranjpe N, Uddin MN, Rahman AS, Asmatulu R. Effects of Surface Treatment on Adhesive Performance of Composite-to-Composite and Composite-to-Metal Joints. Processes. 2024;12(12):2623. doi:10.3390/pr12122623

BibTeX
@article{Paranjpe2024,
  author = {Paranjpe, Nikhil and Uddin, Md. Nizam and Rahman, Akm Samsur and Asmatulu, Ramazan},
  title = {Effects of Surface Treatment on Adhesive Performance of Composite-to-Composite and Composite-to-Metal Joints},
  journal = {Processes},
  year = {2024},
  volume = {12},
  number = {12},
  pages = {2623},
  doi = {10.3390/pr12122623}
}
Kostenlos starten →