EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Understanding the Impact of Sintering Temperature on the Properties of Ni–BCZY Composite Anode for Protonic Ceramic Fuel Cell Application

Nur Hanisah Hadi, Mahendra Rao Somalu, Abdullah Abdul Samat, Wan Nor Anasuhah Wan Yusoff, Andanastuti Muchtar, Nurul Akidah Baharuddin, Muhammed Ali Shaikh Abdul, Jarot Raharjo, Deni Shidqi Khaerudini, Abdalla M. Abdalla, Abul Kalam Azad

Processes · 24.06.2023 · 11 (7) · 1902

DOI: 10.3390/pr11071902 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 24.06.2023. Verfasst von Nur Hanisah Hadi und 10 weiteren Autor:innen. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Higher Education Malaysia through the Fundamental Research Grant Scheme (FRGS), Universiti Kebangsaan Malaysia via the Geran Universiti Penyelidikan (GUP).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Understanding the impact of sintering temperature on the physical and chemical properties of Ni-BaCe0.54Zr0.36Y0.1O3-δ (Ni-BCZY) composite anode is worthy of being investigated as this anode is the potential for protonic ceramic fuel cell (PCFC) application. Initially, NiO–BCZY composite powder with 50 wt% of NiO and 50 wt% of BCZY is prepared by the sol–gel method using citric acid as the chelating agent. Thermogravimetric analysis indicates that the optimum calcination temperature of the synthesised powder is 1100 °C. XRD result shows that the calcined powder exists as a single cubic phase without any secondary phase with the lattice parameter (a) of 4.332 Å. FESEM analysis confirms that the powder is homogeneous and uniform, with an average particle size of 51 ± 16 nm. The specific surface area of the calcined powder measured by the Brunauer–Emmett–Teller (BET) technique is 6.25 m2/g. The thickness, porosity, electrical conductivity and electrochemical performance of the screen-printed anode are measured as a function of sintering temperature (1200–1400 °C). The thickness of the sintered anodes after the reduction process decreases from 28.95 μm to 26.18 μm and their porosity also decreases from 33.98% to 26.93% when the sintering temperature increases from 1200 °C to 1400 °C. The electrical conductivities of the anodes sintered at 1200 °C, 1300 °C and 1400 °C are 443 S/cm, 633 S/cm and 1124 S/cm at 800 °C, respectively. Electrochemical studies showed that the anode sintered at 1400 °C shows the lowest area specific resistance (ASR) of 1.165 Ω cm2 under a humidified (3% H2O) gas mixture of H2 (10%) and N2 (90%) at 800 °C. Further improvement of the anode’s performance can be achieved by considering the properties of the screen-printing ink used for its preparation.

Förderung

  • Ministry of Higher Education Malaysia through the Fundamental Research Grant Scheme (FRGS)
  • Universiti Kebangsaan Malaysia via the Geran Universiti Penyelidikan (GUP)

Zitieren

APA

Hadi, N. H., Somalu, M. R., Samat, A. A., Yusoff, W. N. A. W., Muchtar, A., Baharuddin, N. A., Abdul, M. A. S., Raharjo, J., Khaerudini, D. S., Abdalla, A. M., & Azad, A. K. (2023). Understanding the Impact of Sintering Temperature on the Properties of Ni–BCZY Composite Anode for Protonic Ceramic Fuel Cell Application. Processes, 11(7), 1902. https://doi.org/10.3390/pr11071902

Vancouver

Hadi NH, Somalu MR, Samat AA, Yusoff WNAW, Muchtar A, Baharuddin NA, et al. Understanding the Impact of Sintering Temperature on the Properties of Ni–BCZY Composite Anode for Protonic Ceramic Fuel Cell Application. Processes. 2023;11(7):1902. doi:10.3390/pr11071902

BibTeX
@article{Hadi2023,
  author = {Hadi, Nur Hanisah and Somalu, Mahendra Rao and Samat, Abdullah Abdul and Yusoff, Wan Nor Anasuhah Wan and Muchtar, Andanastuti and Baharuddin, Nurul Akidah and Abdul, Muhammed Ali Shaikh and Raharjo, Jarot and Khaerudini, Deni Shidqi and Abdalla, Abdalla M. and Azad, Abul Kalam},
  title = {Understanding the Impact of Sintering Temperature on the Properties of Ni–BCZY Composite Anode for Protonic Ceramic Fuel Cell Application},
  journal = {Processes},
  year = {2023},
  volume = {11},
  number = {7},
  pages = {1902},
  doi = {10.3390/pr11071902}
}
Kostenlos starten →