EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D Printed Curcuminoid-Loaded Nanocellulose–Alginate Scaffolds with Tunable Mechanical and Diffusion-Controlled Release Properties

Gal Slaček, Petra Kotnik, Željko Knez, Maša Knez Marevci, Silvo Hribernik, Karin Stana Kleinschek, Tamilselvan Mohan

Polysaccharides · 11.07.2026 · 7 (3) · 84

DOI: 10.3390/polysaccharides7030084 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polysaccharides, online erschienen am 11.07.2026. Verfasst von Gal Slaček und 6 weiteren Autor:innen. Die Arbeit nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovenian Research and Innovation Agency.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study reports the fabrication of curcuminoid-loaded nanofibrillated cellulose (NFC)–alginate scaffolds via extrusion-based 3D printing, integrating supercritical CO2 extraction with biofabrication. NFC–alginate inks were pre-crosslinked with CaCl2 (1 to 10 mM) to tune structure and properties. Rheological analysis confirmed shear-thinning behavior suitable for extrusion printing. Mechanical testing revealed a non-linear dependence on crosslinking: optimal performance was achieved by Ink 2 (1 mM CaCl2 with curcuminoid extract), with tensile strength increasing from ~0.60 to ~0.80 MPa and Young’s modulus from ~1.5 to ~3.0 MPa relative (Ink 1, 10 mM CaCl2, without extract), reflecting the combined effect of extract incorporation and ionic pre-crosslinking rather than crosslinker concentration alone; higher crosslinking reduced stiffness (~1.15 MPa). SEM revealed porous architectures (Ink 1: 542 ± 63 μm; Ink 4: 398 ± 71 μm) with increasing structural heterogeneity upon curcuminoid incorporation. In vitro release exhibited biphasic, diffusion-dominated behavior, reaching ~50 to 60% in ethanol-containing media; PBS inclusion as a physiological reference confirmed minimal release (

Förderung

  • Slovenian Research and Innovation Agency

Zitieren

APA

Slaček, G., Kotnik, P., Knez, Ž., Marevci, M. K., Hribernik, S., Kleinschek, K. S., & Mohan, T. (2026). 3D Printed Curcuminoid-Loaded Nanocellulose–Alginate Scaffolds with Tunable Mechanical and Diffusion-Controlled Release Properties. Polysaccharides, 7(3), 84. https://doi.org/10.3390/polysaccharides7030084

Vancouver

Slaček G, Kotnik P, Knez Ž, Marevci MK, Hribernik S, Kleinschek KS, et al. 3D Printed Curcuminoid-Loaded Nanocellulose–Alginate Scaffolds with Tunable Mechanical and Diffusion-Controlled Release Properties. Polysaccharides. 2026;7(3):84. doi:10.3390/polysaccharides7030084

BibTeX
@article{Slaek2026,
  author = {Slaček, Gal and Kotnik, Petra and Knez, Željko and Marevci, Maša Knez and Hribernik, Silvo and Kleinschek, Karin Stana and Mohan, Tamilselvan},
  title = {3D Printed Curcuminoid-Loaded Nanocellulose–Alginate Scaffolds with Tunable Mechanical and Diffusion-Controlled Release Properties},
  journal = {Polysaccharides},
  year = {2026},
  volume = {7},
  number = {3},
  pages = {84},
  doi = {10.3390/polysaccharides7030084}
}
Kostenlos starten →