EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Chitosan-Modified Bentonite as a Controlled-Release Carrier for Tannin: Loading Optimization, Structural Characterization, and Potential Anticorrosion Applications

Raigul Zh. Jumanova, Gulmira S. Beisenova, Gulzhan L. Badavamova, Gulnarkhan Kurmangazhy, Amanbol Alipbayev, Salamat S. Yegeubayeva

Polymers · 11.11.2026 · 18 (22) · 2813

DOI: 10.3390/polym18222813 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 11.11.2026. Verfasst von Raigul Zh. Jumanova und 5 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bentonite-based carriers can be used to control the release of natural corrosion inhibitors. In this study, sodium-activated bentonite was used to load tannin and was subsequently modified with chitosan to regulate tannin release. The effects of contact time and initial pH on tannin loading were investigated using UV-Vis spectrophotometry. The highest adsorption capacity (56.98 ± 0.72 mg g−1) was obtained at an initial pH of 4.5 and a contact time of 12 h. The prepared materials were characterized using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). FTIR results showed changes in the hydroxyl and silicate regions after modification. XRD analysis showed small changes in the basal spacing from 14.42 Å for Bent to 14.88 Å for Bent@Tan and 14.60 Å for Bent@Tan@Chit, indicating that the layered structure was largely preserved. TGA showed an increase in mass loss between 200 and 450 °C from 1.42% for Bent to 2.25% for Bent@Tan and 6.68% for Bent@Tan@Chit, consistent with the presence of additional organic components. Tannin release was investigated in 3.5 wt.% NaCl solution at an initial pH of 5.0 over 48 h. Bent@Tan showed rapid initial release, while Bent@Tan@Chit showed lower early release followed by a gradual increase. Kinetic analysis showed the highest goodness of fit for the first-order model for Bent@Tan (R2 = 0.816) and the zero-order model for Bent@Tan@Chit (R2 = 0.968). These results demonstrate differences in the apparent tannin release profiles of Bent@Tan and Bent@Tan@Chit. The prepared composite may be considered for future studies of anticorrosion coatings; however, its corrosion-inhibiting performance has not yet been experimentally evaluated.

Förderung

  • Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Jumanova, R. Z., Beisenova, G. S., Badavamova, G. L., Kurmangazhy, G., Alipbayev, A., & Yegeubayeva, S. S. (2026). Chitosan-Modified Bentonite as a Controlled-Release Carrier for Tannin: Loading Optimization, Structural Characterization, and Potential Anticorrosion Applications. Polymers, 18(22), 2813. https://doi.org/10.3390/polym18222813

Vancouver

Jumanova RZ, Beisenova GS, Badavamova GL, Kurmangazhy G, Alipbayev A, Yegeubayeva SS. Chitosan-Modified Bentonite as a Controlled-Release Carrier for Tannin: Loading Optimization, Structural Characterization, and Potential Anticorrosion Applications. Polymers. 2026;18(22):2813. doi:10.3390/polym18222813

BibTeX
@article{Jumanova2026,
  author = {Jumanova, Raigul Zh. and Beisenova, Gulmira S. and Badavamova, Gulzhan L. and Kurmangazhy, Gulnarkhan and Alipbayev, Amanbol and Yegeubayeva, Salamat S.},
  title = {Chitosan-Modified Bentonite as a Controlled-Release Carrier for Tannin: Loading Optimization, Structural Characterization, and Potential Anticorrosion Applications},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {22},
  pages = {2813},
  doi = {10.3390/polym18222813}
}
Kostenlos starten →