EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Oscillatory Stiffness Versus Creep–Recovery Response of Recycled High-Density Polyethylene/Waste Engine Oil Modified Bitumen

Hassan Shuaibu Abdulrahman, Michael Chiahemba Iorpenda, Muhammed Fatih Yentimur iD, Ali Almusawi iD, Mustafa Albdairi iD

Polymers · 07.11.2026 · 18 (21) · 2785

DOI: 10.3390/polym18212785 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 07.11.2026. Verfasst von Hassan Shuaibu Abdulrahman und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil Engineering, Federal University of Technology Minna, Minna P.M.B. 65, Niger State, Nigeria. Die Arbeit nennt 75 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Recep Tayyip Erdoğan University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Recycled high-density polyethylene (HDPE) and waste engine oil (WEO) can be combined to modify bitumen, but the high-temperature performance of such binders is often judged from oscillatory measurements alone. This study compares the oscillatory and creep–recovery responses of two long-term-aged HDPE/WEO binders with the same total modifier content but different HDPE:WEO ratios with those of the unmodified base bitumen. Dynamic shear rheometer (DSR) temperature sweeps and multiple stress creep recovery (MSCR) tests, also performed on the DSR, were combined with fractional viscoelastic modeling. Both blends reduced the non-recoverable creep compliance by a factor of 3.8–7.3, so the modification improved the resistance to permanent deformation. In oscillation, however, the blends became more elastic as the temperature increased, whereas in creep, they recovered almost no strain and crept 2–122 times more than predicted from their oscillatory response; the base bitumen was predicted within a factor of 1.6. The creep response of the blends was also four to five times more temperature-sensitive than their oscillatory response. A three-parameter fractional Maxwell model described all creep–recovery cycles and captured the power-law recovery of the blends better than the Burgers model. The results are consistent with an HDPE-rich structure that dominates the oscillatory response but breaks down at MSCR strains, so oscillatory stiffness overstates both the elastic character and the magnitude of the improvement achieved by the binders tested.

Schlagwörter

Stichwörter der Autor:innen

Cox–Merz ruleactivation energyblack diagramfractional viscoelasticitymultiple stress creep recoverynonlinear viscoelasticitypolymer-modified bitumenrecycled high-density polyethylenespringpotwaste engine oil

Autor:innen und Institutionen

  • Department of Civil Engineering, Federal University of Technology Minna, Minna P.M.B. 65, Niger State, Nigeria.
  • Department of Civil Engineering, Faculty of Engineering and Architecture, Recep Tayyip Erdoğan University, Rize 53100, Türkiye.
  • Department of Civil Engineering, Faculty of Engineering, Çankaya University, Ankara 06815, Türkiye.

ORCID-Profile: Muhammed Fatih Yentimur, Ali Almusawi, Mustafa Albdairi

Förderung

  • Recep Tayyip Erdoğan University

Zitieren

APA

Abdulrahman, H. S., Iorpenda, M. C., Yentimur, M. F., Almusawi, A., & Albdairi, M. (2026). Oscillatory Stiffness Versus Creep–Recovery Response of Recycled High-Density Polyethylene/Waste Engine Oil Modified Bitumen. Polymers, 18(21), 2785. https://doi.org/10.3390/polym18212785

Vancouver

Abdulrahman HS, Iorpenda MC, Yentimur MF, Almusawi A, Albdairi M. Oscillatory Stiffness Versus Creep–Recovery Response of Recycled High-Density Polyethylene/Waste Engine Oil Modified Bitumen. Polymers. 2026;18(21):2785. doi:10.3390/polym18212785

BibTeX
@article{Abdulrahman2026,
  author = {Abdulrahman, Hassan Shuaibu and Iorpenda, Michael Chiahemba and Yentimur, Muhammed Fatih and Almusawi, Ali and Albdairi, Mustafa},
  title = {Oscillatory Stiffness Versus Creep–Recovery Response of Recycled High-Density Polyethylene/Waste Engine Oil Modified Bitumen},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {21},
  pages = {2785},
  doi = {10.3390/polym18212785}
}
Kostenlos starten →