EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Beyond the Microscale: Early Nanoscale Changes in Experimental Resin Composites Exposed to Acidic and Alkaline Environments

Farah Elfakhri iD, Giles McCracken iD, Matthew German iD, Rawan N AlKahtani iD

Polymers · 05.11.2026 · 18 (21) · 2755

DOI: 10.3390/polym18212755 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 05.11.2026. Verfasst von Farah Elfakhri und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Conservative Dentistry, Faculty of Dentistry, University of Benghazi, Benghazi P.O. Box 1308, Libya. Die Arbeit nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The study investigates the effects of acidic, neutral, and alkaline environments on the micro- and nanoscale properties of experimental BisGMA/TEGDMA resin composites with varied filler loading. Experimental composites based on BisGMA:TEGDMA at 75:25 wt% with three silica-glass filler loadings (75, 40, and 0 wt%) were stored at 37 °C in phosphate-buffered saline (PBS; pH 7.2), citric acid (pH 3.8), or sodium hydroxide (NaOH; pH 11) for up to 28 days. Microscale changes were assessed using sorption, Vickers hardness, and scanning electron microscopy (SEM), while atomic force microscopy (AFM) was used to evaluate nanoscale surface roughness and Young’s modulus. Storage medium did not significantly affect percentage mass increase (p = 0.092) or Vickers hardness (p = 0.098). Higher filler loading was associated with lower mass increase (ρ = −0.902, p < 0.001) and greater hardness (r = 0.660, p < 0.0001). SEM revealed surface degradation, particularly at the filler–matrix interface following NaOH exposure. Nanoscale surface roughness was negatively associated with filler loading (ρ = −0.368, p = 0.001), with changes observed predominantly in unfilled materials after 28 days. AFM measurements demonstrated a shift towards lower Young’s modulus values after only one day of exposure to citric acid and NaOH, whereas the reduction in PBS occurred later. Acidic and alkaline exposure produced limited alterations in conventional microscale measures but more changes in surface morphology and nanoscale properties. These exploratory findings suggest that AFM-derived Young’s modulus may detect early softening following acidic and alkaline exposure, suggesting its potential utility for characterizing early changes associated with chemical ageing than conventional microscale measurements.

Schlagwörter

Stichwörter der Autor:innen

BisGMATEGDMAYoung’s modulusatomic force microscopychemical degradationpHresin composite

Autor:innen und Institutionen

  • Department of Conservative Dentistry, Faculty of Dentistry, University of Benghazi, Benghazi P.O. Box 1308, Libya.
  • School of Dental Sciences, Newcastle University, Framlington Place, Newcastle-upon-Tyne NE2 4BW, UK.
  • Department of Clinical Dental Sciences, College of Dentistry, Princess Nourah bint Abdulrahman University, P.O. Box 84428, Riyadh 11671, Saudi Arabia.

ORCID-Profile: Farah Elfakhri, Giles McCracken, Matthew German, Rawan N AlKahtani

Zitieren

APA

Elfakhri, F., McCracken, G., German, M., & AlKahtani, R. N. (2026). Beyond the Microscale: Early Nanoscale Changes in Experimental Resin Composites Exposed to Acidic and Alkaline Environments. Polymers, 18(21), 2755. https://doi.org/10.3390/polym18212755

Vancouver

Elfakhri F, McCracken G, German M, AlKahtani RN. Beyond the Microscale: Early Nanoscale Changes in Experimental Resin Composites Exposed to Acidic and Alkaline Environments. Polymers. 2026;18(21):2755. doi:10.3390/polym18212755

BibTeX
@article{Elfakhri2026,
  author = {Elfakhri, Farah and McCracken, Giles and German, Matthew and AlKahtani, Rawan N},
  title = {Beyond the Microscale: Early Nanoscale Changes in Experimental Resin Composites Exposed to Acidic and Alkaline Environments},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {21},
  pages = {2755},
  doi = {10.3390/polym18212755}
}
Kostenlos starten →