EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of a Heating System on Waste Plastic Pyrolysis in a Fixed-Bed Reactor

Saša Papuga iD, Sergio Brutti iD, Stefano Vecchio Ciprioti iD, Omar Al Zeer iD

Polymers · 01.11.2026 · 18 (21) · 2702

DOI: 10.3390/polym18212702 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 01.11.2026. Verfasst von Saša Papuga und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Technology, University of Banja Luka, 78000 Banja Luka, Bosnia and Herzegovina. Die Arbeit nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Plastic pyrolysis performance depends not only on nominal reactor temperature but also on the actual temperature field established within the reacting bed and vapor phase. This study investigates how the heating-system configuration of a laboratory fixed-bed reactor affects product yields and pyrolysis-oil composition during waste polypropylene pyrolysis. Experiments were performed at 475 °C under N2 at 0.1 L min−1 for 60 min, comparing a single PID-controlled internal heater with a dual configuration using two independently controlled heating systems. Dual heating increased mean oil yield from 52.14 to 83.95% and reduced gas yield from 45.87 to 14.55%, while solid residue decreased from 1.99 to 1.50%. Temperature profiles showed pronounced overheating in the central vapor-phase region during single heating, whereas dual heating maintained a more homogeneous profile close to the set point. ATR-FTIR, 1H NMR, and elemental analysis further showed that the dual-heating oil was more aliphatic, with the aliphatic proton fraction increasing from 80.8 to 88.7% and the mean atomic H/C ratio increasing from 2.019 to 2.135. These results demonstrate that heating configuration can substantially alter both yield distribution and liquid-product chemistry even at the same nominal reactor temperature.

Schlagwörter

Stichwörter der Autor:innen

fixed-bed reactorheating modehot spotsplastic pyrolysispyrolysis-oil composition

Autor:innen und Institutionen

  • Faculty of Technology, University of Banja Luka, 78000 Banja Luka, Bosnia and Herzegovina.
  • Department of Chemistry, Sapienza University of Rome, 00185 Rome, Italy.
  • Department of Basic and Applied Sciences for Engineering, Sapienza University of Rome, 00161 Rome, Italy.

ORCID-Profile: Saša Papuga, Sergio Brutti, Stefano Vecchio Ciprioti, Omar Al Zeer

Zitieren

APA

Papuga, S., Brutti, S., Vecchio Ciprioti, S., & Al Zeer, O. (2026). Effects of a Heating System on Waste Plastic Pyrolysis in a Fixed-Bed Reactor. Polymers, 18(21), 2702. https://doi.org/10.3390/polym18212702

Vancouver

Papuga S, Brutti S, Vecchio Ciprioti S, Al Zeer O. Effects of a Heating System on Waste Plastic Pyrolysis in a Fixed-Bed Reactor. Polymers. 2026;18(21):2702. doi:10.3390/polym18212702

BibTeX
@article{Papuga2026,
  author = {Papuga, Saša and Brutti, Sergio and Vecchio Ciprioti, Stefano and Al Zeer, Omar},
  title = {Effects of a Heating System on Waste Plastic Pyrolysis in a Fixed-Bed Reactor},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {21},
  pages = {2702},
  doi = {10.3390/polym18212702}
}
Kostenlos starten →