EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Numerical Modeling of Orthogonal Cutting in 3D-Printed PEEK: Process Parameters and Simulation Validation

David Gómez-García iD, Jose Díaz-Álvarez iD, George Youssef, Antonio Díaz-Álvarez iD

Polymers · 24.10.2026 · 18 (21) · 2639

DOI: 10.3390/polym18212639 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 24.10.2026. Verfasst von David Gómez-García und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, University Carlos III of Madrid, Avd. de la Universidad 30, Leganés, 28911 Madrid, Spain. Die Arbeit nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Information.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) is rapidly transforming industrial production by offering a low-waste and highly customizable alternative to traditional subtractive methods. However, tight dimensional tolerances and complex geometries often require post-process machining of 3D-printed components. Among high-performance thermoplastics, polyether-ether-ketone (PEEK) is preferred for its thermal stability and mechanical strength. A key novelty of this study addresses a critical gap in the literature: while some analyses of PEEK machining consider cutting and pressure parameters, few documented instances examine unreinforced PEEK at high cutting speeds. This knowledge gap is highly relevant because the absence of reinforcement and high cutting speeds interact through temperature-induced thermal softening. Utilizing a validated finite element model in ABAQUS, the research presents a comprehensive numerical investigation of the orthogonal micromachining of 3D-printed PEEK, analyzing the influence of printing parameters (building orientation and strategy) alongside machining variables (cutting speed and depth of cut). The study identifies critical anisotropic effects, where specific build orientations, particularly −45°, maximize mechanical resistance and heat generation. Conversely, multi-layer stacking sequences (e.g., 0°/90° and 45°/−45°) are shown to enhance structural rigidity and improve surface finish by optimizing chip formation mechanics and reducing interfacial temperatures. These findings provide a consistent framework for optimizing the post-processing of additively manufactured advanced polymers.

Schlagwörter

Stichwörter der Autor:innen

PEEKdamagemicromachiningnumerical modelingorthogonal cuttingtemperature

Autor:innen und Institutionen

  • Department of Mechanical Engineering, University Carlos III of Madrid, Avd. de la Universidad 30, Leganés, 28911 Madrid, Spain.
  • Experimental Mechanics Laboratory, Mechanical Engineering Department, San Diego State University, 5500 Campanile Dr, San Diego, CA 92182, USA.

ORCID-Profile: David Gómez-García, Jose Díaz-Álvarez, Antonio Díaz-Álvarez

Förderung

  • Ministry of Science and Information

Zitieren

APA

Gómez-García, D., Díaz-Álvarez, J., Youssef, G., & Díaz-Álvarez, A. (2026). Numerical Modeling of Orthogonal Cutting in 3D-Printed PEEK: Process Parameters and Simulation Validation. Polymers, 18(21), 2639. https://doi.org/10.3390/polym18212639

Vancouver

Gómez-García D, Díaz-Álvarez J, Youssef G, Díaz-Álvarez A. Numerical Modeling of Orthogonal Cutting in 3D-Printed PEEK: Process Parameters and Simulation Validation. Polymers. 2026;18(21):2639. doi:10.3390/polym18212639

BibTeX
@article{GmezGarca2026,
  author = {Gómez-García, David and Díaz-Álvarez, Jose and Youssef, George and Díaz-Álvarez, Antonio},
  title = {Numerical Modeling of Orthogonal Cutting in 3D-Printed PEEK: Process Parameters and Simulation Validation},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {21},
  pages = {2639},
  doi = {10.3390/polym18212639}
}
Kostenlos starten →