EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermomechanical Properties of Carbon and Glass Fiber-Reinforced Epoxy Composites as Function of Drilling Parameters

Satılmış Ürgün iD, Sinan Fidan iD, Eser Yarar iD, Mehmet İskender Özsoy iD, Mustafa Özgür Bora iD

Polymers · 22.09.2026 · 18 (19) · 2316

DOI: 10.3390/polym18192316 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 22.09.2026. Verfasst von Satılmış Ürgün und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Aviation Electrics and Electronics, Faculty of Aeronautics and Astronautics, Kocaeli University, 41001 Kocaeli, Türkiye. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Dry drilling experiments were carried out on pure and hybrid carbon/glass fiber-reinforced epoxy laminates, viz., all carbon (C8), all glass (G8), glass-faced hybrid (G2C4G2), and carbon-faced hybrid (C2G4C2), using the newly designed high-speed steel (HSS) flow step drill. Drilling operations were conducted at three drill diameters (4, 6, 8 mm), three spindle speeds (125, 250, 535 rpm), and a constant feed rate of 0.1 mm/rev. The thermomechanical behavior and hole-quality assessments were done by means of in-process thrust force monitoring, infrared thermography, 3D optical surface roughness, and scanning electron microscopy (SEM). Drill diameter had a non-linear impact on the thrust force and peak temperature, the highest values of which were obtained with the 6 mm diameter drill, due to its characteristic cutting engagement stages. Both mechanical and thermal behaviors depended on the composite material composition and stacking sequence: the G8 laminate had the lowest thrust force and the most dimensionally stable holes, the C8 laminate had a low thrust force and minimal thermal reaction, but created exit burrs, whereas hybrid laminates had the maximum thrust force and peak temperature (reaching 103.5 °C) along with the maximum entry/exit asymmetry caused by dissimilar carbon/glass ply interfaces. Spindle speed had little effect on the thrust force and was the main parameter affecting the peak temperature (having a 51.78% contribution). Analysis of variance (ANOVA) and multivariate analysis of variance (MANOVA) revealed the drill diameter, material structure, and their interaction as the significant parameters (p < 0.0001) of the coupled thermomechanical drilling response.

Schlagwörter

Stichwörter der Autor:innen

HSS flow step drillMANOVAdelaminationdrillinghybrid carbon/glass laminatepolymer–matrix compositesthrust force

Autor:innen und Institutionen

  • Department of Aviation Electrics and Electronics, Faculty of Aeronautics and Astronautics, Kocaeli University, 41001 Kocaeli, Türkiye.
  • Department of Airframe & Powerplant Maintenance, Faculty of Aeronautics and Astronautics, Kocaeli University, 41001 Kocaeli, Türkiye.
  • Department of Mechanical Engineering, Faculty of Engineering, Kocaeli University, 41380 Kocaeli, Türkiye.
  • Department of Mechanical Engineering, Faculty of Engineering, Sakarya University, 54050 Sakarya, Türkiye.

ORCID-Profile: Satılmış Ürgün, Sinan Fidan, Eser Yarar, Mehmet İskender Özsoy, Mustafa Özgür Bora

Zitieren

APA

Ürgün, S., Fidan, S., Yarar, E., Özsoy, M. İ., & Bora, M. Ö. (2026). Thermomechanical Properties of Carbon and Glass Fiber-Reinforced Epoxy Composites as Function of Drilling Parameters. Polymers, 18(19), 2316. https://doi.org/10.3390/polym18192316

Vancouver

Ürgün S, Fidan S, Yarar E, Özsoy Mİ, Bora MÖ. Thermomechanical Properties of Carbon and Glass Fiber-Reinforced Epoxy Composites as Function of Drilling Parameters. Polymers. 2026;18(19):2316. doi:10.3390/polym18192316

BibTeX
@article{rgn2026,
  author = {Ürgün, Satılmış and Fidan, Sinan and Yarar, Eser and Özsoy, Mehmet İskender and Bora, Mustafa Özgür},
  title = {Thermomechanical Properties of Carbon and Glass Fiber-Reinforced Epoxy Composites as Function of Drilling Parameters},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {19},
  pages = {2316},
  doi = {10.3390/polym18192316}
}
Kostenlos starten →