EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Adhesion and Hydrothermal Performance of Epoxy–Dicyandiamide Adhesive Film for PMMA-PETR

Guoliang Yu iD, Lei Wang, Yue Li, Hu Lyu, Dongzhou Sun, Wei Dong, Shudi Liu, Yanting Du, Kexin Ning, Dawei Zhang iD, Zhiqiang Ning, Xianzhi Kong

Polymers · 05.08.2026 · 18 (15) · 1918

DOI: 10.3390/polym18151918 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 05.08.2026. Verfasst von Guoliang Yu und 11 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Petrochemistry, Heilongjiang Academy of Sciences, Harbin 150040, China. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Foundation of Heilongjiang Province, Foundation of Heilongjiang Academy of Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Epoxy/dicyandiamide adhesive film is required for the bonding of polymethyl methacrylate (PMMA) aircraft cockpit edges. An imidazole/alkanolamine composite accelerator was developed to satisfy the requirement of maintaining a bonding temperature below 90 °C for this structure, successfully reducing the curing temperature of the adhesive film from 180 °C to 85 °C. The curing process of the low-temperature curing adhesive film and its hydrothermal aging resistance after curing were investigated using mechanical testing, Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). The results indicate that the curing process of 85 °C for 6 h enables the adhesive film to fulfill the adhesion strength requirements for aircraft cockpit edge applications. The cured adhesive film is found to exhibit limited intrinsic water resistance due to its low crosslinking density. Therefore, external edge sealing is required in practical engineering applications to isolate moisture. This work provides an application-specific one-component epoxy/dicyandiamide adhesive film for the low-temperature flexible bonding of aviation PMMA cockpit edges to PETR, and clarifies its adhesion performance and hydrothermal aging behavior under the target service scenario.

Schlagwörter

Stichwörter der Autor:innen

curing processepoxy/dicyandiamide adhesive filmhydrothermal aging performanceimidazole/alkanolamine composite accelerator

Autor:innen und Institutionen

  • Institute of Petrochemistry, Heilongjiang Academy of Sciences, Harbin 150040, China.
  • AVIC Shenyang Aircraft Design and Research Institute, Shenyang 110035, China.
  • State Key Laboratory of Woody Oil Resources Utilization, Northeast Forestry University, Harbin 150040, China.

ORCID-Profile: Guoliang Yu, Dawei Zhang

Förderung

  • Natural Science Foundation of Heilongjiang Province
  • Foundation of Heilongjiang Academy of Sciences

Zitieren

APA

Yu, G., Wang, L., Li, Y., Lyu, H., Sun, D., Dong, W., Liu, S., Du, Y., Ning, K., Zhang, D., Ning, Z., & Kong, X. (2026). Adhesion and Hydrothermal Performance of Epoxy–Dicyandiamide Adhesive Film for PMMA-PETR. Polymers, 18(15), 1918. https://doi.org/10.3390/polym18151918

Vancouver

Yu G, Wang L, Li Y, Lyu H, Sun D, Dong W, et al. Adhesion and Hydrothermal Performance of Epoxy–Dicyandiamide Adhesive Film for PMMA-PETR. Polymers. 2026;18(15):1918. doi:10.3390/polym18151918

BibTeX
@article{Yu2026,
  author = {Yu, Guoliang and Wang, Lei and Li, Yue and Lyu, Hu and Sun, Dongzhou and Dong, Wei and Liu, Shudi and Du, Yanting and Ning, Kexin and Zhang, Dawei and Ning, Zhiqiang and Kong, Xianzhi},
  title = {Adhesion and Hydrothermal Performance of Epoxy–Dicyandiamide Adhesive Film for PMMA-PETR},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {15},
  pages = {1918},
  doi = {10.3390/polym18151918}
}
Kostenlos starten →