EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Al2O3 and SiC Fillers on the Structure and Properties of UHMWPE-Based Composite Coatings Produced by Flame Spraying

Mazhyn Skakov, Perassyl Zhanimkhan iD, Danel Skakov, Dastan Buitkenov, Meruyert Maulet iD, Aiym Nabioldina iD

Polymers · 30.07.2026 · 18 (15) · 1879

DOI: 10.3390/polym18151879 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 30.07.2026. Verfasst von Mazhyn Skakov und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Physics and Technologies, Sarsen Amanzholov East Kazakhstan University, Ust-Kamenogorsk 070000, Kazakhstan. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakh-stan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the structure and properties of flame-sprayed composite coatings based on ultra-high molecular weight polyethylene (UHMWPE) modified with Al2O3 and SiC ceramic fillers. The results of the composite coatings showed that the filler particles were preserved within the polymer matrix, covered by polymer fibers, and strongly bonded to the matrix. The X-ray diffraction analysis showed that for the samples containing Al2O3, the degree of crystallinity decreased from 77% to 64%, while for the SiC-containing samples, it remained in the range of 71–76%. The maximum microhardness was achieved in the coating with 15 wt.% Al2O3, reaching 8.15 ± 0.5 HV0.03, which represents a 50.9% increase compared with the initial UHMWPE coating. In the case of the SiC filler, the maximum microhardness was achieved at a content of 20 wt.%, reaching 7.40 ± 0.4 HV0.03. The abrasive wear test results demonstrated that both fillers enhanced the wear resistance of the coatings. The coatings containing 15–20 wt.% SiC exhibited the highest wear resistance, with a mass loss of approximately 0.02 g. In the case of the Al2O3 filler, the minimum mass loss was achieved at a content of 20 wt.%, reaching approximately 0.032 g.

Schlagwörter

Stichwörter der Autor:innen

Al2O3 coatingSiC coatingUHMWPEabrasive wearcomposite coatingflame sprayingmicrohardness

Autor:innen und Institutionen

  • Department of Physics and Technologies, Sarsen Amanzholov East Kazakhstan University, Ust-Kamenogorsk 070000, Kazakhstan.
  • Agency of the Republic of Kazakhstan for Atomic Energy, National Nuclear Center of the Republic of Kazakhstan, Kurchatov 071100, Kazakhstan.
  • Altay Polymetals LLP, Almaty 100835, Kazakhstan.

ORCID-Profile: Perassyl Zhanimkhan, Meruyert Maulet, Aiym Nabioldina

Förderung

  • Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakh-stan

Zitieren

APA

Skakov, M., Zhanimkhan, P., Skakov, D., Buitkenov, D., Maulet, M., & Nabioldina, A. (2026). Effect of Al2O3 and SiC Fillers on the Structure and Properties of UHMWPE-Based Composite Coatings Produced by Flame Spraying. Polymers, 18(15), 1879. https://doi.org/10.3390/polym18151879

Vancouver

Skakov M, Zhanimkhan P, Skakov D, Buitkenov D, Maulet M, Nabioldina A. Effect of Al2O3 and SiC Fillers on the Structure and Properties of UHMWPE-Based Composite Coatings Produced by Flame Spraying. Polymers. 2026;18(15):1879. doi:10.3390/polym18151879

BibTeX
@article{Skakov2026,
  author = {Skakov, Mazhyn and Zhanimkhan, Perassyl and Skakov, Danel and Buitkenov, Dastan and Maulet, Meruyert and Nabioldina, Aiym},
  title = {Effect of Al2O3 and SiC Fillers on the Structure and Properties of UHMWPE-Based Composite Coatings Produced by Flame Spraying},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {15},
  pages = {1879},
  doi = {10.3390/polym18151879}
}
Kostenlos starten →