Development and Performance Evaluation of a Temperature- and Salt-Resistant Bio-Based Profile-Control and Oil Displacement System
Polymers · 20.07.2026 · 18 (14) · 1768
DOI: 10.3390/polym18141768 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 20.07.2026. Verfasst von Xianglong Yu und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Engineering Science, University of Chinese Academy of Sciences, Beijing 100049, China. Die Arbeit nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: PetroChina Company Limited.
Abstract (Originalsprache)
High-temperature and high-salinity reservoirs (typically referring here to temperatures ≥ 100 °C and salinities > 100 g/L) impose stringent requirements on chemical flooding and profile-control agents, particularly in terms of thermal stability, salt tolerance, injectivity, and environmental compatibility. In this study, a bio-based composite mobility-control and oil-displacement system was developed by combining carbonized corn-straw particles with the biopolymer scleroglucan. Corn-straw biomass particles were prepared by pyrolysis at 500 °C followed by ball milling for 2 h. Their particle-size distribution, elemental composition, and suspension stability were characterized, and the rheological behavior, thermal and salt tolerance, long-term aging stability, injectivity, plugging performance, and enhanced-oil-recovery efficiency of the composite system were evaluated systematically. The average particle size decreased from 25.6 μm for mechanically ground straw to 2.8 μm after carbonization and ball milling. The H/C atomic ratio of the carbonized particles was 0.31, indicating enhanced aromatization and structural stability. A scleroglucan concentration of 1000 ppm provided a suspension rate of 97%, balancing suspension stability and chemical dosage. The composite system maintained stable viscosity and viscoelasticity from 30 to 130 °C in deionized water, saturated NaCl solution, and saturated CaCl2 solution, with viscosity loss below 10%. After sealed anaerobic aging at 100 °C for 28 days, the viscosity retention remained above 90%. Sand-pack tests showed stable injectivity in media with permeabilities of 1235 and 2064 mD and a plugging efficiency of 95.7% in a 2846 mD model. In oil-displacement experiments, the composite system increased the final recovery factor from 46.6% for scleroglucan flooding alone to 53.3%, corresponding to an additional 6.7 percentage points. These results demonstrate that the carbonized biomass particle-scleroglucan system has promising thermal stability, salt tolerance, plugging capacity, and oil-displacement performance, providing a potential green strategy for mobility control in harsh reservoir environments.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Engineering Science, University of Chinese Academy of Sciences, Beijing 100049, China.
- Institute of Porous Flow and Fluid Mechanics, Chinese Academy of Sciences, Langfang 065007, China.
- PetroChina Research Institute of Petroleum Exploration and Development, Beijing 100083, China.
Förderung
- PetroChina Company Limited
Zitieren
APA
Yu, X., Guan, B., Huang, L., Xin, Y., Leng, K., & Xiu, J. (2026). Development and Performance Evaluation of a Temperature- and Salt-Resistant Bio-Based Profile-Control and Oil Displacement System. Polymers, 18(14), 1768. https://doi.org/10.3390/polym18141768
Vancouver
Yu X, Guan B, Huang L, Xin Y, Leng K, Xiu J. Development and Performance Evaluation of a Temperature- and Salt-Resistant Bio-Based Profile-Control and Oil Displacement System. Polymers. 2026;18(14):1768. doi:10.3390/polym18141768
BibTeX
@article{Yu2026,
author = {Yu, Xianglong and Guan, Baoshan and Huang, Lixin and Xin, Yilin and Leng, Kaiqi and Xiu, Jianlong},
title = {Development and Performance Evaluation of a Temperature- and Salt-Resistant Bio-Based Profile-Control and Oil Displacement System},
journal = {Polymers},
year = {2026},
volume = {18},
number = {14},
pages = {1768},
doi = {10.3390/polym18141768}
}
EUVIMED