EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of the Physical Recycling of Acrylonitrile–Butadiene–Styrene (ABS) Plastics on the Properties of the Final Product

Juliana Aristéia de Lima iD, Ruud Cuypers, Anders Höije, Ignacy Jakubowicz iD, Richard Sott, Nazdaneh Yarahmadi

Polymers · 13.07.2026 · 18 (14) · 1716

DOI: 10.3390/polym18141716 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 13.07.2026. Verfasst von Juliana Aristéia de Lima und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Polymer, Fiber and Composite, RISE Research Institutes of Sweden, 431 53 Mölndal, Sweden. Die Arbeit nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union’s Horizon 2020 Research and Innovation Programme.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Acrylonitrile butadiene styrene (ABS) is widely used as an engineering plastic, but its extensive use generates a significant amount of waste that is difficult to recycle due to the material’s complex composition. In this study, the physical recycling of ABS using the dissolution technique has been employed to separate the pure copolymer of styrene and acrylonitrile (SAN) from polybutadiene rubber (PBR) and other substances. The relationships between the properties and composition of the original ABS materials were investigated as a starting point and for reference values to evaluate the effects of recycling on the quality and safety of recycled materials. Three different ABS materials were used in the recycling process from which pure SAN polymers were produced. The recycled SANs were then melt-blended with fresh masterbatch. The final ABS materials had the same composition, which facilitated investigation of whether the use of SAN recycled from different sources results in any differences in the properties of the final ABS material. The results showed that all the properties of ABS materials made with recycled SAN are similar regardless of the source of SAN. Several chemical substances were quantified in the original ABS materials and in SAN polymers obtained through the recycling process. The substances were largely removed from all materials except one. The main conclusions from this study are that the quality of ABS materials made with recycled SAN is at the same level as that of virgin ABS and is independent of the source from which SAN comes. This study has also shown that chemical safety is satisfactory because the physical recycling process is able to remove most of the substances that were present in the original ABS materials.

Schlagwörter

Stichwörter der Autor:innen

acrylonitrile–butadiene–styreneanalysis of impuritiesdissolution processmaterial characterizationphysical recyclingpolybutadiene rubber

Autor:innen und Institutionen

  • Department of Polymer, Fiber and Composite, RISE Research Institutes of Sweden, 431 53 Mölndal, Sweden.
  • TNO, Kesslerpark 1, 2288 GS Rijswijk, The Netherlands.
  • Division Built Environment, RISE Research Institutes of Sweden, 400 22 Göteborg, Sweden.

ORCID-Profile: Juliana Aristéia de Lima, Ignacy Jakubowicz

Förderung

  • European Union’s Horizon 2020 Research and Innovation Programme

Zitieren

APA

de Lima, J. A., Cuypers, R., Höije, A., Jakubowicz, I., Sott, R., & Yarahmadi, N. (2026). Effects of the Physical Recycling of Acrylonitrile–Butadiene–Styrene (ABS) Plastics on the Properties of the Final Product. Polymers, 18(14), 1716. https://doi.org/10.3390/polym18141716

Vancouver

de Lima JA, Cuypers R, Höije A, Jakubowicz I, Sott R, Yarahmadi N. Effects of the Physical Recycling of Acrylonitrile–Butadiene–Styrene (ABS) Plastics on the Properties of the Final Product. Polymers. 2026;18(14):1716. doi:10.3390/polym18141716

BibTeX
@article{deLima2026,
  author = {de Lima, Juliana Aristéia and Cuypers, Ruud and Höije, Anders and Jakubowicz, Ignacy and Sott, Richard and Yarahmadi, Nazdaneh},
  title = {Effects of the Physical Recycling of Acrylonitrile–Butadiene–Styrene (ABS) Plastics on the Properties of the Final Product},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {14},
  pages = {1716},
  doi = {10.3390/polym18141716}
}
Kostenlos starten →