EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mobility-Driven Design of PDMS-Modified Glassy Polymer Networks for Thermally Activated Shape Memory in Vat Photopolymerization

Yura Choi, Namchul Cho

Polymers · 07.07.2026 · 18 (13) · 1678

DOI: 10.3390/polym18131678 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 07.07.2026. Verfasst von Yura Choi und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Energy Engineering, Soonchunhyang University, Asan 31538, Republic of Korea. Die Arbeit nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Korea Institute of Energy Technology Evaluation and Planning (KETEP), Ministry of Climate, Energy & Environment (MCEE) of the Republic of Korea, Soonchunhyang University Research Fund.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Glass-transition-driven shape memory polymers are promising materials for 4D printing because their thermally activated transition enables programmed deformation and recovery without relying on melting or crystallization-driven switching. In this study, PDMS-MMA-modified photocurable networks were designed for vat photopolymerization-based 4D printing by varying PDMS-MMA content and switching monomer structure while maintaining a fixed TMPTMA crosslinker content. The resin formulations were prepared using tert-butyl acrylate (tBA) or isobornyl acrylate (IBOA) as switching monomers, PDMS-MMA as a flexible mobility-regulating segment, and TMPTMA as a multifunctional crosslinker. The effects of formulation composition on printability, network formation, thermal stability, thermomechanical transition, mechanical properties, and shape memory behavior were systematically investigated. FT-IR analysis confirmed effective photocuring of the acrylate/methacrylate networks, while rheological evaluation showed that resin viscosity depended on monomer structure and PDMS-MMA content. DMA results revealed thermomechanical transition, although some formulations exhibited broad tan δ responses due to network heterogeneity and distributed segmental relaxation. Based on resin printability, printed-part resolution, and relatively well-defined tan δ transitions, T-15 and I-15 were selected as representative formulations for quantitative shape memory evaluation. Shape memory testing was conducted under force-control mode because stable strain-controlled programming was not achievable for the printed specimens. Both T-15 and I-15 exhibited high shape fixity over two programming–recovery cycles. I-15 showed stable recovery behavior with recovery ratios of 91.51% and 95.87%, whereas T-15 showed apparent over-recovery with recovery ratios exceeding 100%, likely due to residual stress release during reheating. Overall, these results demonstrate that thermally activated shape-memory performance is governed not only by the nominal transition temperature but also by the coupled effects of PDMS-mediated segmental mobility, switching monomer structure, mechanical integrity, and elastic energy storage within a fixed crosslinked network framework.

Schlagwörter

Stichwörter der Autor:innen

4D printingglass transition modulationmobility–crosslink designpolydimethylsiloxaneshape memory polymers

Autor:innen und Institutionen

  • Department of Energy Engineering, Soonchunhyang University, Asan 31538, Republic of Korea.

Förderung

  • Korea Institute of Energy Technology Evaluation and Planning (KETEP)
  • Ministry of Climate, Energy & Environment (MCEE) of the Republic of Korea
  • Soonchunhyang University Research Fund

Zitieren

APA

Choi, Y., & Cho, N. (2026). Mobility-Driven Design of PDMS-Modified Glassy Polymer Networks for Thermally Activated Shape Memory in Vat Photopolymerization. Polymers, 18(13), 1678. https://doi.org/10.3390/polym18131678

Vancouver

Choi Y, Cho N. Mobility-Driven Design of PDMS-Modified Glassy Polymer Networks for Thermally Activated Shape Memory in Vat Photopolymerization. Polymers. 2026;18(13):1678. doi:10.3390/polym18131678

BibTeX
@article{Choi2026,
  author = {Choi, Yura and Cho, Namchul},
  title = {Mobility-Driven Design of PDMS-Modified Glassy Polymer Networks for Thermally Activated Shape Memory in Vat Photopolymerization},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {13},
  pages = {1678},
  doi = {10.3390/polym18131678}
}
Kostenlos starten →