EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development and Characterization of High-Density Polyethylene/Polylactic Acid/Titanium Dioxide Composites for Pellet-Based 3D Printing

Ildiko Peter iD, Dan-Cristian Craciun, Mihai Alin Pop iD

Polymers · 12.06.2026 · 18 (12) · 1475

DOI: 10.3390/polym18121475 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 12.06.2026. Verfasst von Ildiko Peter und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Industrial Engineering and Management, Faculty of Engineering and Information Technology, George Emil Palade University of Medicine, Ph…. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present study, the development of a high-density polyethylene/polylactic acid/titanium dioxide (HDPE–PLA–TiO2) composite proposed for pellet-based additive manufacturing and the evaluation of its thermal and mechanical behavior are presented and discussed. The study was designed to address the printability limitations of high-HDPE-content systems, particularly extrusion instability and weak interlayer adhesion. PLA was introduced to improve processing stability, while TiO2 was incorporated as an inorganic filler. The selected formulation allowed the production of filaments, pellets, and 3D-printed specimens. Thermal analysis indicated the absence of significant mass loss below approximately 300 °C under the applied thermogravimetric/differential thermal analysis (TG/DTA) conditions, suggesting that no major mass-loss degradation occurred within the selected processing window. However, this result should be interpreted as macroscopic thermal stability and does not exclude possible molecular-level changes in PLA during processing. Tensile tests indicated strengths of 20–25 MPa for extruded filaments and 7.86–10.36 MPa for printed specimens, with an elastic modulus of approximately 2 GPa. Scanning Electron microscopy equipped with Energy Dispersive X-Ray Spectroscopy (SEM/EDS) observations revealed a heterogeneous fracture morphology with cavities, microcracks, fibrillar structures, and local Ti-rich regions, supporting the influence of morphology and filler distribution on the mechanical response of the printed specimens. The results indicate improved printability, adequate thermal behavior for the selected processing conditions, and moderate but reproducible tensile performance, highlighting the potential of this formulation for pellet-based additive manufacturing applications where processability and rigidity are more relevant than maximum tensile strength.

Schlagwörter

Stichwörter der Autor:innen

high-density polyethylenepellet-based 3D printingpolylactic acidpolymer compositesthermal degradationtitanium dioxide

Autor:innen und Institutionen

  • Department of Industrial Engineering and Management, Faculty of Engineering and Information Technology, George Emil Palade University of Medicine, Pharmacy, Science, and Technology of Targu Mures, 540142 Targu Mures, Ro…
  • Doctoral School of I.O.S.U.D., George Emil Palade University of Medicine, Pharmacy, Science, and Technology of Targu Mures, 540142 Targu Mures, Romania.
  • Materials Science Department, Transilvania University of Brasov, 500036 Brasov, Romania.

ORCID-Profile: Ildiko Peter, Mihai Alin Pop

Zitieren

APA

Peter, I., Craciun, D. C., & Pop, M. A. (2026). Development and Characterization of High-Density Polyethylene/Polylactic Acid/Titanium Dioxide Composites for Pellet-Based 3D Printing. Polymers, 18(12), 1475. https://doi.org/10.3390/polym18121475

Vancouver

Peter I, Craciun DC, Pop MA. Development and Characterization of High-Density Polyethylene/Polylactic Acid/Titanium Dioxide Composites for Pellet-Based 3D Printing. Polymers. 2026;18(12):1475. doi:10.3390/polym18121475

BibTeX
@article{Peter2026,
  author = {Peter, Ildiko and Craciun, Dan-Cristian and Pop, Mihai Alin},
  title = {Development and Characterization of High-Density Polyethylene/Polylactic Acid/Titanium Dioxide Composites for Pellet-Based 3D Printing},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {12},
  pages = {1475},
  doi = {10.3390/polym18121475}
}
Kostenlos starten →