EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Characterization of the Interlaminar Fracture Toughness of an Additive Manufacturing Continuous Glass Fiber-Reinforced Thermoplastic Composite

Jonnathan D Santos iD, Fernando Crespo Beltrán, Mateo Berrezueta, Alexander Torres, Alex Gavilanes Álvarez, Alfredo Valarezo iD

Polymers · 09.06.2026 · 18 (12) · 1438

DOI: 10.3390/polym18121438 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 09.06.2026. Verfasst von Jonnathan D Santos und 5 weiteren Autor:innen. Beteiligte Einrichtung: Análisis y Tecnología de Estructuras en Ingeniería (ATEI), Universidad Politécnica Salesiana, Cuenca 010105, Ecuador. Die Arbeit nennt 76 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Politecnica Salesiana University, Universidad Politécnica Salesiana.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

There is a lack of knowledge concerning the interlaminar fracture toughness of 3D-printed composite materials using both commercial filament composites and fused deposition modeling (FDM) technology from Markforged®. In this investigation, additive manufacturing (AM) continuous fiber-reinforced thermoplastic (cFRT) specimens have been tested to characterize the initiation and propagation of interlaminar fracture toughness in mode I (GI). Unidirectional glass fiber (GF)-reinforced polyamide 6 (PA) laminates were characterized by means of the double cantilever beam (DCB) test. These specimens were manufactured using a MarkTwo® printer and tested without doublers, following a laminate configuration selected according to appropriate experimental findings reported in the state of the art, ensuring reliable fracture characterization. The experimental results exhibited repeatability and strong agreement between the modified compliance calibration (MCC) and modified beam theory (MBT) reduction methods. The resistance curve (R-curve) indicated a progressive increase in fracture resistance during crack propagation. To analyze the experienced failure mechanism during testing, the fracture surfaces of representative post-mortem DCB specimens were observed using a scanning electron microscope (SEM), revealing characteristic morphological features at two magnification levels. Moreover, representative cross-sections of the tested DCB specimens were electronically observed to analyze the interlaminar morphologies, showing an irregular and random distribution of the matrix, fiber, and voids between consecutive plies and adjacent deposited rasters. Compared with previously reported Markforged® continuous fiber-reinforced systems, the GF/PA composite material exhibited intermediate initiation fracture toughness but lower propagation toughness. This study contributes to filling the existing gap in fracture toughness data for glass fiber-reinforced additively manufactured composites.

Schlagwörter

Stichwörter der Autor:innen

3D-printed compositefused filament fabricationglass fiber-reinforced polyamideinterlaminar fracture toughnessmechanical testing

Autor:innen und Institutionen

  • Análisis y Tecnología de Estructuras en Ingeniería (ATEI), Universidad Politécnica Salesiana, Cuenca 010105, Ecuador.
  • Department of Engineering, University of Campania "Luigi Vanvitelli", 81031 Aversa, Italy.
  • Institute for Energy and Materials, Mechanical Engineering Department, Universidad San Francisco de Quito, Quito 170901, Ecuador.

ORCID-Profile: Jonnathan D Santos, Alfredo Valarezo

Förderung

  • Politecnica Salesiana University
  • Universidad Politécnica Salesiana

Zitieren

APA

Santos, J. D., Crespo Beltrán, F., Berrezueta, M., Torres, A., Álvarez, A. G., & Valarezo, A. (2026). Characterization of the Interlaminar Fracture Toughness of an Additive Manufacturing Continuous Glass Fiber-Reinforced Thermoplastic Composite. Polymers, 18(12), 1438. https://doi.org/10.3390/polym18121438

Vancouver

Santos JD, Crespo Beltrán F, Berrezueta M, Torres A, Álvarez AG, Valarezo A. Characterization of the Interlaminar Fracture Toughness of an Additive Manufacturing Continuous Glass Fiber-Reinforced Thermoplastic Composite. Polymers. 2026;18(12):1438. doi:10.3390/polym18121438

BibTeX
@article{Santos2026,
  author = {Santos, Jonnathan D and Crespo Beltrán, Fernando and Berrezueta, Mateo and Torres, Alexander and Álvarez, Alex Gavilanes and Valarezo, Alfredo},
  title = {Characterization of the Interlaminar Fracture Toughness of an Additive Manufacturing Continuous Glass Fiber-Reinforced Thermoplastic Composite},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {12},
  pages = {1438},
  doi = {10.3390/polym18121438}
}
Kostenlos starten →