EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Drilling Characteristics of Additively Manufactured PLA/17-4 PH Stainless Steel Hybrid Composite: Thrust Force, Surface Roughness, Vibration and Temperature Change

Erhan Şentürk iD, Cem Alparslan iD, Ramazan Ötüken iD, Muhammed Furkan Erhan iD, Şenol Bayraktar iD

Polymers · 08.06.2026 · 18 (12) · 1434

DOI: 10.3390/polym18121434 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 08.06.2026. Verfasst von Erhan Şentürk und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Faculty of Engineering and Architecture, Recep Tayyip Erdoğan University, Rize 53100, Türkiye. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 75 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Recep Tayyip Erdoğan University Development Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Understanding the finishing behavior of hybrid structures produced by additive manufacturing based on FDM is critically important in systems where phases with different thermal and mechanical properties coexist. In this study, the drilling performance of hybrid structures with a PLA/17-4 PH/PLA layer arrangement was comprehensively investigated in terms of thrust force, moment, surface roughness, temperature variation, vibration behavior, and surface integrity. For this purpose, a total of 16 drilling tests were performed on 56 × 56 × 15 mm hybrid specimens with 100% infill density, in a full factorial configuration, at cutting speeds (V) of 80–170 m/min and feed rates (f) of 0.04–0.16 mm/rev. The middle layer was used in the as-printed green state as a 17-4 PH metal-filled filament containing metal particles and binder, without any debinding or sintering step. The results showed that increasing feed rate increased thrust force, moment, and surface roughness in all layers, whereas increasing cutting speed decreased these values and promoted a more stable drilling regime. The middle 17-4 PH layer exhibited lower surface roughness than the outer PLA layers, while thermal measurements indicated limited variation at the hole entrance and higher temperature accumulation at the hole exit. The most favorable drilling condition within the studied hybrid configuration was obtained at 170 m/min and 0.04 mm/rev, whereas the least favorable condition was obtained at 80 m/min and 0.16 mm/rev. Overall, the combination of high cutting speed and low feed rate provided the most suitable drilling window for the studied hybrid structure. The findings also indicated that surface quality was more strongly associated with cutting load and high-frequency vibration components than with vibration level alone.

Schlagwörter

Stichwörter der Autor:innen

FDMcomposite materialdrillinghybrid additive manufacturingvibration

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Faculty of Engineering and Architecture, Recep Tayyip Erdoğan University, Rize 53100, Türkiye.
  • FDM and Metallography Laboratory, Department of Mechanical Engineering, Recep Tayyip Erdoğan University, Rize 53100, Türkiye.
  • Department of Electronic Automation, Vocational School of Technical Sciences, Recep Tayyip Erdoğan University, Rize 53100, Türkiye.
  • Department of Manufacturing Engineering, Faculty of Technology, Gazi University, Ankara 06560, Türkiye.

ORCID-Profile: Erhan Şentürk, Cem Alparslan, Ramazan Ötüken, Muhammed Furkan Erhan, Şenol Bayraktar

Förderung

  • Recep Tayyip Erdoğan University Development Foundation

Zitieren

APA

Şentürk, E., Alparslan, C., Ötüken, R., Erhan, M. F., & Bayraktar, Ş. (2026). Drilling Characteristics of Additively Manufactured PLA/17-4 PH Stainless Steel Hybrid Composite: Thrust Force, Surface Roughness, Vibration and Temperature Change. Polymers, 18(12), 1434. https://doi.org/10.3390/polym18121434

Vancouver

Şentürk E, Alparslan C, Ötüken R, Erhan MF, Bayraktar Ş. Drilling Characteristics of Additively Manufactured PLA/17-4 PH Stainless Steel Hybrid Composite: Thrust Force, Surface Roughness, Vibration and Temperature Change. Polymers. 2026;18(12):1434. doi:10.3390/polym18121434

BibTeX
@article{entrk2026,
  author = {Şentürk, Erhan and Alparslan, Cem and Ötüken, Ramazan and Erhan, Muhammed Furkan and Bayraktar, Şenol},
  title = {Drilling Characteristics of Additively Manufactured PLA/17-4 PH Stainless Steel Hybrid Composite: Thrust Force, Surface Roughness, Vibration and Temperature Change},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {12},
  pages = {1434},
  doi = {10.3390/polym18121434}
}
Kostenlos starten →